Contact No. 07020814816 / 08087778631
Address: - G 17/8, Tarapur MIDC, Boisar West, Palghar, Maharashtra India 401506
Stanrose® AC Cleaner Plus
“STANROSE® AC CLEANER PLUS” is a powerful cleaning agent for cleaning of diesel engine air coolers, scavenging air systems and the compressor side of turbochargers. “STANROSE® AC CLEANER PLUS” is a micro-emulsion type cleaner, where a synergistic blend of biodegradable surfactants and low toxicity solvents replace the use of the harmful solvents traditionally used in air cooler cleaners without reducing the cleaning performance. It is formulated to meet the latest environmental standards, and is non toxic both to the environment and to persons handling it. “STANROSE® AC CLEANER PLUS” contains no chlorinated or aromatic hydrocarbon solvents, nonylphenol ethoxylates or other substances harmful to the environment.
Advance Air Cooler Cleaner
Features and Benefits
Efficient and economical
Form - Liquid
Appearance - Pale Yellow
Density - 1.0
Flash Point - Above 610°C
pH in Conc. - 9
Not Compatible May swell rubber and synthetic rubber.
Meets the latest environmental standards
Equal cleaning performance to traditional cleaners based on harmful chlorinated solvents
Low toxicity, low evaporation and pleasant smell
Formulated to remove oil, grease and carbon deposits from air coolers and scavenging systems
Maintains, stabilises and maximises air cooler efficiency
Leaves no residue and has no harmful effect on engine.
Can be used for hand spray cleaning while diesel engine is stationary
Ideal for use in soak bath or cleaning tanks, such as the Chemical Cleaning Unit and the Ultrasonic Bath
Method of Application
Recirculation method in-situ
For this cleaning procedure the engine needs to be stopped and secured. Permanently installed spray nozzles in combination with a cleaning solution tank and pump, such as the Stanrose Chemical Cleaning Unit should be used. It is advised to blind off the cooler outlet. Properly mix water and 10-30% “STANROSE® AC CLEANER PLUS”, depending on the severity of the contamination, in the tank. Connect the pump's outlet to the nozzle assembly and the air cooler drain to the tank. Start the pump and spray the solution through the nozzles over the entire surface of the cooler and drain back to the tank. Circulate the solution for a period of 1 to 6 hours. After cleaning, rinse with fresh water. Remove the outlet blind and disconnect the pump and tank loop.
Soaking method in-situ
For this cleaning procedure the engine needs to be stopped and secured. Blind off the cooler outlet and flood the cooler with a solution of 10-30% “STANROSE® AC CLEANER PLUS” in water depending on the severity of the contamination. Soak for a period of 1 to 6 hours and drain to slop tank. Agitation by means of steam or compressed air will improve the cleaning effect. After cleaning, rinse with fresh water. Remove outlet blind and close drain.
Out of Service Cleaning :
Soak bath method
Remove the cooler from the engine and place in a soak bath filled with a solution of 10-30% “STANROSE® AC CLEANER PLUS” in water for a period of 1-6 hours. Agitation by means of steam or compressed air will improve the cleaning effect. After cleaning rinse with fresh water and reinstall the cooler. This method is also suitable for machine parts with stubborn carbon deposits.
Hand spray method
For this cleaning procedure the engine needs to be stopped and secured. Open the inspection cover on top of the cooler and the drain valve. Spray undiluted “STANROSE® AC CLEANER PLUS” into the tube nest, with e.g. a Stanrose Jet Spray Unit, and allow to penetrate into the deposits for a minimum of 1 hour. Rinse thoroughly with a high pressure jet such as a Stanrose High Pressure Machine. Close inspection cover and drain.
The general principle is to inject a solution of “STANROSE® AC CLEANER PLUS” into the air trunking upstream of the charge air cooler followed by a clean water rinse. For efficient cleaning of air coolers, it is necessary to use correctly installed dosing and injection equipment. To calculate the amount of solution required to clean an air cooler, calculate or find the cross-sectional area of the cooler and use 3 litres of cleaning solution per square meter or as table below:
Engine HP - Solution mix. with 25% Stanrose® AC Cleaner Plus
6,000 to 12,000 - 3 litre mix
12,000 to 24,000 - 4.5 litre mix
24,000 or more - 6 litre mix
For in-service cleaning of air coolers and the air-side of turbochargers, a solution of 25% “STANROSE® AC CLEANER PLUS” in freshwater is recommended.
The appropriate dosage of cleaner is then placed in the dosing pot and injected up stream of the air cooler for a period of 10 minutes. After a further 10 minutes, a similar quantity of fresh water is injected to rinse off the emulsified deposits.
Rate and frequency of application depends mainly on the condition of the air coolers. However when starting with the use of “STANROSE® AC CLEANER PLUS”, recommended injection is every 24 hours. After the initial cleaning period, the cleaning effect should last for 48 hours of operational time. Although frequency of cleaning may vary, the calculated cleaning dose should remain the same. This cleaning method is only recommended if approved by the engine
Storage and Handling
Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated.
Store at moderate temperatures in dry, well-ventilated area.