Contact No. 07020814816 / 08087778631
Address: - G 17/8, Tarapur MIDC, Boisar West, Palghar, Maharashtra India 401506
Stanrose® Tank Clean - Brite
Stanrose® Tank Clean HD is a micro emulsion water based tank cleaner. This product is low toxic, biodegradable and safe to use. It contains natural solvents linked with easily biodegradable surfactants. Main application is for hydrocarbon freeing but it may also be used for other tank cleaning purposes where a strong degreasing effect is required.
Tank Clean Bright (Rust Remover)
Features and Benefits
Does not contain nonylphenol ethoxylates or other estrogenic compounds
Splits aŌer cleaning, releasing the oil phase for reclamation
Micro emulsion based formulation that combines the performance of a water and solvent based product into one low toxic product
Helps with rapid hydrocarbon freeing of tanks.
Appearance water White
Density 1, 0
pH, in Conc 7-5
Non-Compatible May soften some rubber and synthetic rubber
Our tank cleaning capabilities includes the following types of tanks and more:
Petroleum (gasoline, diesel, propane, jet fuel, etc.)
Chemical (caustic, acid, ammonia, resin, lead, etc.)
Crude Oil (light, heavy, sweet, sour, etc.)
Asphalt, Clay Waste, Waste Water
Food Grade Tanks
Rail Tank Cars
Portable Storage Tanks
Underground Storage Tanks
Ocean Going Vessel Fuel and Cargo Tanks
Odor and VOC Control
Specialized Pumping & Product Transfers
6" Submersible Guzzler Sludge Pumps (700 gpm)
2" - 3" Diaphragm Pumps (60-140 gpm)
6" - 4" Trash Pumps (750-1,800 gpm)
High Head Pumps, Electric and Other Sludge Pumps
Guzzler and Turbo Vac Units
Hydroblasting (High & Low Pressure)
Removal of Floor Coatings
Door Sheet Cuƫng
Vacuum Truck Services
Roll-Off Bin Storage, Transportation & Disposal
Waste and Water Minimization/Processing
Emergency Tank Cleaning Services
Method of Application
Spraying : This can be beneficial as part of the initial cleaning process after the carriage of Lube oils and Lube oil additives. As soon as the tank in question has been checked empty by the attending surveyor, Stanrose® Tank Clean HD " should be sprayed over all surfaces which are safely reachable.
Portable Machines : After 45 minutes the butterworth machines should be operated for 3 x 20 minutes drops using warm 60o C, then the machines brought back to the top and a full hot wash 80 – 85 o C should be carried out for at least 6 hours.
Fixed Machines : Wash ambient for 45 minutes followed by warm water for one cycle before increasing to hot (80oC) for 4 hours.
Injection : This can be carried out by injecting "Stanrose® Tank Clean HD " into the butterworth system after the heater. A normal amount to use would be 100 – 150 liters during the initial washing cycle. Water temperature should be 60o C during the injection period then brought up to 80 – 85 o C for the full washing period.
Re-circulation : Possibly the best result are achieved by re-circulating a solution of "Stanrose® Tank Clean HD " after the initial rough washing of the tank. A sufficient amount of fresh water to maintain good suction should be heated to 60 o C and approximately 420 liters of "Stanrose® Tank Clean HD " (2 drums) added for each 500 liters of fresh water. The temperature of the mixture can be increased depending upon the melting point if the product being cleaned. The solution should be circulated for at least 4 hours and the butterworth machines operated at maximum pressure in all areas of the tank throughout this process. If a number of tanks are to be circulated, then a substantial quantity of solution can be made so that transfers can be made without delay and any small amounts lost will not affect the operation. Normally following transfer to another tank, 100 liters "Stanrose® Tank Clean HD " is added for each 5000 liters of solution. This is called “spiking”.
Following the re-circulation process, the tank must be hot butterworthed 80-85o C for at least 6 hours.
*Use a strainer at the pumpstack when circulating any solution "Stanrose® Tank Clean HD " is recommended for local cleaning and degreasing and may be applied by brush, hand spray, immersion, soaking or any other conventional means. Apply concentrate "Stanrose® Tank Clean HD " over soiled area and wait for 20-30 minutes before rinsing off with water.
Soak Method : For heavy oil and soil Put parts to be cleaned into a bath of concentrate "Stanrose® Tank Clean HD " and for medium to light soiling use a solution of 10-30% "Stanrose® Tank Clean HD " in water. Parts should be soaked for at least 30 minutes before washing off with water.
Spray-Method : Spray concentrate "Stanrose® Tank Clean HD " over all soiled areas. With in 15 and 30 minutes, "Stanrose® Tank Clean HD " starts its function then rinse off by water hose. For stubborn deposits, agitation by scrubbing will assist the cleaning operation .
Cargo Tank Cleaning after Mineral Oils
Direct injection method : Make a solution of "Stanrose® Tank Clean HD " between 0.1 and 2.0% i.e. one to twenty litres per ton wash water. Then use with Tank cleaning machine , Best results are obtained when water is heated to a temperature between 60 to 80°C. Slops Should be Constantly Stripped from, tank.
Recirculation method / Ship's Rocking Motion : Make solution Strength with "Stanrose® Tank Clean HD " between 0.5 –3 % and used with Tank Cleaning machines OR fill the tank to 20-30% volume with sea water and add the RXSOL-20-2001-210 up to full dose . For better results heat the solution between 60 - 80°C.
NOTE : Dose rate and results will vary depending on amount of contamination.
Spot cleaning- "Stanrose® Tank Clean HD " (concentrate) can be sprayed over surfaces and left for 20 - 30 minutes Finally wash down the tank surfaces with hot water between 60°C and 80°C with high pressure machine . Keep stripping tank slops and transfer to holding tank/slop tank. Cleaning of the Oil side of Lube Oil Heat Exchangers Cleaning is best achieved by the recirculation method using a heated 20% solution of "Stanrose® Tank Clean HD ".
First of all drain off any remaining oil from Heat Exchanger.
Connect the discharge side of a portable pump to the lower heat exchanger connection & the suction Side of the pump to the bottom outlet of a 200 litre drum.
Complete the circuit by connecting the upper connection on the heat exchanger to the top of the drum.
Maintain the bath temperature between 60-80 0 C throughout the cleaning operation. If it is not possible to heat, the operation will need to be extended.
Use the pump to maintain circulation for 12 to 15 hours. When the cleaning is completed, disconnect the lower heat exchanger connection and drain out the cleaning solution.
Connect a fresh water supply to the upper heat exchanger connection, and rinse until the water runs clean from the lower connection. When rinsing is complete, disconnect the water supply and thoroughly drain and dry the heat exchanger
Storage and Handling
Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water.
In case of contact with eyes, treat with large volumes of water and see a physician.
Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection.
Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated.
Store at moderate temperatures in dry, well-ventilated area.