Search Results

Stanrose® Degreaser - M Stanrose® Degreaser-M is an Environmentally Sensible, heavy duty, non-flammable, non-hazardous, mildly alkaline aqueous carbon remover and degreaser. The product carries a complete corrosion Inhibition package and rinse aid technology. Formulated specifically for cleaning stainless steel, carbon steel, aluminum alloys and all other ferrous and non ferrous metals. Cleans all Types of soils including sulphur based cutting fluids, adhesives, carbon, dirt, oils, grinding, finishing & polishing compounds, water & solvent based inks Carbon, Dirt, Cutting Fluids. Common Name Metal Degreaser Product Code STAN-CLC102 Features and Benefits Can be used safely on all metal Easy to use Leaves smooth, clean surface Just wipe on and wipe off Restores and protects Technical Properties Appearance : Clear liquid – Concentrated Flash Point : >200 Seta Flash Odour : Mild Surface Tension (dynes/cm 24) (water = 1.0) : 24 pH (Full Strength) : 11.50 - 11.70 pH (10% solution in water @ 68 ºF) : 10.80 - 11.00 Ideal Operating Temp (ºF) : 110°F - 160°F Ideal Operating Concentration : 8 - 15% Specific Gravity : 1.070 - 1.080 (@ 68 ºF) Weight/Gal. : 9.00 (lbs. /gal.) Recommended Uses Cleans all Types of soils including sulphur based cutting fluids, adhesives, carbon, dirt, oils, grinding, finishing & polishing compounds, water & solvent based inks Carbon, Dirt, Cutting Fluids. Method of Application Stanrose® Degreaser-M should be used full strength OR diluted down 8 - 15% concentration with water at an operating temperature range of 110o F - 160o F (MAXIMUM OPERATING TEMPERATURE 160 º F). Hand wipe, solution spray, mechanical, or ultrasonic agitation is used to enhance the cleaning action. For carbon, dry oil, grease, polymers, adhesives or inks, soak the parts until residues are removed. Parts can be wiped with a damp rag or rinsed off with warm water. Use filtered hot air to dry out the parts. Storage and Handling Direct contact of Stanrose® Degreaser-M will cause a strong skin or eye irritation, it is important to utilize recommended gloves (18 mil thick natural rubber), safety goggles and other suitable protective clothing your company recommends. Harmful if inhaled or swallowed. Do not take internally. Keep out of reach of children; Use product with adequate ventilation. If splashed in eyes or on skin, wash off with plenty of water. If swallowed remove from exposure area, do not induce vomiting, washout mouth thoroughly with water and drink several glasses of water. Keep at rest. Call a physician immediately. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Bio-Degreaser HP Stanrose® Bio Degeaser - HP is a non-emulsifying degreaser based on a blend of high boiling hydrocarbons and surfaceactive components. It is suited to remove most mineral oils, greases and preserving agents. Safe to use on most metals. Undiluted at a temperature of ± 20 °C it can also be used on most synthetics, paints, lacquers, epoxy and zinc silicate coatings. Common Name Tank Clean – Bio Degreaser Product Code STAN-CLC116 Features and Benefits Water-based degreaser Does not contain nonylphenol ethoxylates or other estrogenic compounds Low-toxic Non-flammable Splits after cleaning, releasing the oil phase for reclamation Micro emulsion based formulation that combines the performance of a water and solvent based product into one low toxic product Helps with rapid hydrocarbon freeing of tanks Technical Properties Appearance - Water white Density [g/ml] - 1.0 Form - Liquid pH - 7.5 Recommended Uses TANK CLEANING - Suitable to remove light oily-like contaminations like alcohols, benzines, fuel oils and liquid / slight viscous surfactants like fatty-alcohol ethoxylates etc. SPRAYING - Stanrose® Bio Degeaser - HP is sprayed undiluted on the objects that are to be cleaned. GENERAL MAINTENANCE - This product can also be used to clean floors in workshops, engine rooms etc. It is often used as de-preserving agent. NOTICE: Objects where rust is to be avoided, should afterwards not be sprayed off with water but with pure (unused) Stanrose® Bio Degeaser - HP. Colourless liquid based on hydrocarbons and surface active components. Non-emulsifying in water and safe to use on most metals. Method of Application TANK CLEANING – CIRCULATION METHOD For the removal of light oily-like contaminations like alcohols, benzines, fuel oils, a dilution of 3 – 5 % is sufficient. For the removal of liquid surfactants like fatty-alcohol ethoxylates etc., a dilution of 8 – 10 % should be used. In case the surfactants are viscous (especially surfactants with an ethoxylationgrade of 15 and higer), the cleaning solution should be heated to max. 55 °C. Recommended tank - cleaning procedure for removing stains from tank linings using Stanrose® Bio Degeaser - HP. 1. Mix solutions of Bio Degreaser 165 either in tank bottom or void space. 2. Dilution rate with water between 3 % and 10 %, depending upon light or heavy contamination (see above). Recent experience has shown that a 7 % - 7.5 % solution secures successful cleaning. 3. Do not use the entire quantity of Bio Degreaser 165 in one solution for all tanks to be cleaned. Save a few drums (2 – 3) to “boost” the solution for cleaning the last 20 % - 25 % of the tanks to be cleaned. 4. The solution may be used at ambient temperature, however, it is suggested that an increase of the cleaning temperature to maximum 55 °C will enhance the cleaning ability and shorten the cleaning time. 5. Proceed to recycle the cleaning solution through the tank washing system for a period of two hours minimum per machine drop. Usually a cleaning time of 4 hours per tank will prove sufficient. 6. At completion of chemical application begin washing down with water, using maximum pressure available. 7. Inspect tank surfaces and if there remain some stains, spot clean with undiluted Stanrose® Bio Degeaser - HP directly on the stained area. Allow a reaction time of 30 minutes and then rinse with water. Storage and Handling Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. To clean floors, machines and engines, the pure product should be used to moisturize the objects. During the 20 to 60 minutes working time, brushing may help the cleaning process. Spray off afterwards using a high pressure water jet. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Degreaser HD Stanrose® Degresol HD is a versatile heavy duty degreaser meant for tough industrial cleaning jobs. It emulsifies greasy, oily soil for easy and complete removal. A special low foam formulation makes this water based cleaner / degreaser ideal for use in automatic floor scrubbing machines. It eliminates costly work stoppages due to foam build-up in the recovery tank. This product is economical and versatile. Its varied dilution ratios enable use in a wide range of applications, from heavy duty degreasing to general purpose cleaning. When used in pressure sprayers, it generates cleaning power without over abundant suds. Common Name Heavy Duty Degreaser Product Code STAN-CLC070 Features and Benefits Non-butyl emulsifier is concentrated for fast action in the toughest oily and greasy soils. Emulsifies oily soils on industrial equipment, parts, soak tanks, tools and engines. Excellent for food service filters, fans, vent hoods, grills, ovens and other surfaces. General cleaner for floors and counters. Technical Properties Physical State: Liquid Colour: Clear Fragrance: None Foaming: Low Free Rinsing: Yes Petroleum Distillates: None Viscosity: Thin Phosphates: None Biodegradable: Yes pH (undiluted): 12.8 Recommended Uses Prepare dilution based on the amount and type of soil to be cleaned. Apply to floor, allow to work, and agitate with mop or brush, pick up and rinse if needed. Method of Application Heavy Soil: 1:16 to 1:8 (8-16 ounces of per gal. of water) Normal Soil: 1:32 to 1:16 (4-8 ounces of per gal. of water) Light Soil: 1:64 to 1:32 (2-4 ounces of per gal. of water) Pressure Cleaning Equipment: Use 2nd SHIFT in the equipment in accordance with the equipment manufacturer's instructions. Adjust use dilution strength for optimum cleaning. Rinse with hot or cold clean water. Floor Cleaning: Add 2nd SHIFT to the cleaning solution tank after filling it with water. Adjust use dilution strength to optimize cleaning results and efficiency. Mopping Equipment: Dilute between 1:50 and 1:5 (2-25 ounces per gallon of water) Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Cement Remover Stanrose® Cement Remover is designed to instantly penetrate and disperse cement, providing complete cleaning of cement cargo deposits, dry cement stains and lime deposits. The product is capable of cleaning hard cement deposits perfectly while removing the possible existing rust. Stanrose® Cement Remover is water based and non-flammable containing powerful acids, inhibitors for surface protection and efficient detergents. Common Name Cement Remover Product Code ​ Features and Benefits Heavy duty acid-based product. Effectively removes cement / cement clinkers cargo deposits, dry cement stains and lime. Helps with removing possible existing rust. Quick and intrinsic action. Contains powerful inhibitors for surface protection. Safe to use on rubber/plastic. Water-soluble, non-flammable. Free from hydrocarbon or chlorinated solvents. Cost effective, easy to apply and use. Technical Properties Specific gravity - 1.16 gr/cm3 at 15°C Solubility in water - Appreciable pH (1% Solution) - 1 Odor - Pungent Recommended Uses Safe to use on all metal surfaces and parts except aluminium, zinc, tin and its alloys. It is highly recommended to always test all cleaner solutions on a small area of tank coating, before full scale application. Method of Application A. Dosage Undiluted: In cases where we deal with heavy deposit build–up, CEMENT REMOVER must be applied undiluted. Diluted: In cases of light deposition, on large surface areas, a solution between 10–40% may be used. B. Cleaning Procedure Undiluted/Diluted: In parts such as corner cavities, tank skeleton inlets, etc, CEMENT REMOVER must be carefully poured and/or applied by conventional means such as a hard brush, mop, sponge or any other manual devices feasible to move with rapid and irregular action. Let it soak for 15 minutes. Afterwards, wash thoroughly by applying high–pressure water source. In case of deposit persistence, repeat the cleaning procedure. Storage and Handling CEMENT REMOVER is considered a highly corrosive product. Operators must consult the Safety and Handling instructions table before use. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Fuel Demulsion Stanrose® Fuel Demulsification is the breaking of a crude oil emulsion into oil and water phases. Common Name Fuel Emulsion Breaker Product Code STAN-FOT191 Features and Benefits From a process point of view, the oil producer is interested in three aspects of fuel demulsification : Rate or the speed at which this separation takes place Amount of water left in the crude oil after separation Quality of separated water for disposal Technical Properties Stanrose® Fuel Demulsification is an aid to the physical removal of water from all grades of fuel. Recommended Uses Stanrose® Fuel Demulsification improves centrifugal separation of fines, it helps prevent sludge formation and stabilises fuel viscosity. The fuel filters and lines will be cleaner with less inclination towards blockage. The main purpose of Stanrose® Fuel Demulsification is however to rapidly split water in oil emulsions. Method of Application Breaks water-in-oil emulsions by lowering the surface tension between the two phases. It is insoluble in water and remains effective even after the water has been removed. Powerful dispersants combat existing sludge formations while homogenizing the fuel to prevent new sludge from being formed. Stanrose® Fuel Demulsification lowers the surface tension between the oil and water phases in an emulsion. It is completely insoluble in water and remains in the fuel oil phase. It also disperses sludges and any heavy particles into thefuel oil. Dosing Instructions: Stanrose® Fuel Demulsification is dosed to the bunker tank prior or during bunkering. Dosing is based on water content using test results. If none are available an initial dose of 1:4000 should be used. Water % Vol 0.5 – 1.0 1.0 – 2.00 >2.0 Dose Rate 1: 4000 1 : 2000 1 : 1000 Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Stanpol-B-300 Stanrose® Stanpol-B-300 Toilet cleaner prevents the build-up of stains in the toilet bowl and keeps it visibly clean with effective removal of germs in the toilet Common Name Toilet Cleaner Liquid Product Code STAN-CLC090 Features and Benefits ​ Technical Properties Appearance : Clear. Color : blue space Form : aqueous solution Odor : Wintergreen Flash point :> 199.94 °F (> 93.3 °C) Tagliabue Physical state Liquid pH :< 1 (Strongly acidic) Specific gravity: 1.040 - 1.050 Solubility (H2O): Complete Recommended Uses ​ Method of Application ​ Storage and Handling Eye contact If in eyes, IMMEDIATELY rinse eyes thoroughly with water. Remove any contact lenses and continue rinsing eyes for at least 15 minutes. Immediately call a physician or Poison Control Center. Skin contact If on skin, IMMEDIATELY wash with soap and water. Immediately call a physician or Poison Control Center. Inhalation If inhaled, move person to fresh air. Immediately call a physician or Poison Control Center for further advice. Ingestion If swallowed, do NOT induce vomiting. Rinse mouth and drink a glass of water. IMMEDIATELY call a Physician or Poison Control Center. Notes to physician Contains hydrochloric acid. Probable mucosal damage may contraindicate the use of gastric lavage. Packing Available ​ Download File

Stanrose® Tank Clean - Brite Stanrose® Tank Clean HD is a micro emulsion water based tank cleaner. This product is low toxic, biodegradable and safe to use. It contains natural solvents linked with easily biodegradable surfactants. Main application is for hydrocarbon freeing but it may also be used for other tank cleaning purposes where a strong degreasing effect is required. Common Name Tank Clean Bright (Rust Remover) Product Code STAN-CLC058 Features and Benefits Water-based degreaser Does not contain nonylphenol ethoxylates or other estrogenic compounds Low-toxic Non-flammable Splits aŌer cleaning, releasing the oil phase for reclamation Micro emulsion based formulation that combines the performance of a water and solvent based product into one low toxic product Helps with rapid hydrocarbon freeing of tanks. Technical Properties Form Liquid Appearance water White Density 1, 0 pH, in Conc 7-5 Non-Compatible May soften some rubber and synthetic rubber Recommended Uses Our tank cleaning capabilities includes the following types of tanks and more: Petroleum (gasoline, diesel, propane, jet fuel, etc.) Chemical (caustic, acid, ammonia, resin, lead, etc.) Crude Oil (light, heavy, sweet, sour, etc.) Asphalt, Clay Waste, Waste Water Food Grade Tanks Rail Tank Cars Water Tanks Portable Storage Tanks Underground Storage Tanks Ocean Going Vessel Fuel and Cargo Tanks Tank Degassing Odor and VOC Control Specialized Pumping & Product Transfers 6" Submersible Guzzler Sludge Pumps (700 gpm) 2" - 3" Diaphragm Pumps (60-140 gpm) 6" - 4" Trash Pumps (750-1,800 gpm) High Head Pumps, Electric and Other Sludge Pumps Guzzler and Turbo Vac Units Hydroblasting (High & Low Pressure) Removal of Floor Coatings Door Sheet Cuƫng Line Flushing Vacuum Truck Services Roll-Off Bin Storage, Transportation & Disposal Waste and Water Minimization/Processing SuperMACS Sludge Bug Centrifuge Oil/Product Recovery Water Recycling Emergency Tank Cleaning Services Method of Application Spraying : This can be beneficial as part of the initial cleaning process after the carriage of Lube oils and Lube oil additives. As soon as the tank in question has been checked empty by the attending surveyor, Stanrose® Tank Clean HD " should be sprayed over all surfaces which are safely reachable. Portable Machines : After 45 minutes the butterworth machines should be operated for 3 x 20 minutes drops using warm 60o C, then the machines brought back to the top and a full hot wash 80 – 85 o C should be carried out for at least 6 hours. Fixed Machines : Wash ambient for 45 minutes followed by warm water for one cycle before increasing to hot (80oC) for 4 hours. Injection : This can be carried out by injecting "Stanrose® Tank Clean HD " into the butterworth system after the heater. A normal amount to use would be 100 – 150 liters during the initial washing cycle. Water temperature should be 60o C during the injection period then brought up to 80 – 85 o C for the full washing period. Re-circulation : Possibly the best result are achieved by re-circulating a solution of "Stanrose® Tank Clean HD " after the initial rough washing of the tank. A sufficient amount of fresh water to maintain good suction should be heated to 60 o C and approximately 420 liters of "Stanrose® Tank Clean HD " (2 drums) added for each 500 liters of fresh water. The temperature of the mixture can be increased depending upon the melting point if the product being cleaned. The solution should be circulated for at least 4 hours and the butterworth machines operated at maximum pressure in all areas of the tank throughout this process. If a number of tanks are to be circulated, then a substantial quantity of solution can be made so that transfers can be made without delay and any small amounts lost will not affect the operation. Normally following transfer to another tank, 100 liters "Stanrose® Tank Clean HD " is added for each 5000 liters of solution. This is called “spiking”. Following the re-circulation process, the tank must be hot butterworthed 80-85o C for at least 6 hours. *Use a strainer at the pumpstack when circulating any solution "Stanrose® Tank Clean HD " is recommended for local cleaning and degreasing and may be applied by brush, hand spray, immersion, soaking or any other conventional means. Apply concentrate "Stanrose® Tank Clean HD " over soiled area and wait for 20-30 minutes before rinsing off with water. Soak Method : For heavy oil and soil Put parts to be cleaned into a bath of concentrate "Stanrose® Tank Clean HD " and for medium to light soiling use a solution of 10-30% "Stanrose® Tank Clean HD " in water. Parts should be soaked for at least 30 minutes before washing off with water. Spray-Method : Spray concentrate "Stanrose® Tank Clean HD " over all soiled areas. With in 15 and 30 minutes, "Stanrose® Tank Clean HD " starts its function then rinse off by water hose. For stubborn deposits, agitation by scrubbing will assist the cleaning operation . Cargo Tank Cleaning after Mineral Oils Direct injection method : Make a solution of "Stanrose® Tank Clean HD " between 0.1 and 2.0% i.e. one to twenty litres per ton wash water. Then use with Tank cleaning machine , Best results are obtained when water is heated to a temperature between 60 to 80°C. Slops Should be Constantly Stripped from, tank. Recirculation method / Ship's Rocking Motion : Make solution Strength with "Stanrose® Tank Clean HD " between 0.5 –3 % and used with Tank Cleaning machines OR fill the tank to 20-30% volume with sea water and add the chemical up to full dose . For better results heat the solution between 60 - 80°C. NOTE : Dose rate and results will vary depending on amount of contamination. Spot cleaning- "Stanrose® Tank Clean HD " (concentrate) can be sprayed over surfaces and left for 20 - 30 minutes Finally wash down the tank surfaces with hot water between 60°C and 80°C with high pressure machine . Keep stripping tank slops and transfer to holding tank/slop tank. Cleaning of the Oil side of Lube Oil Heat Exchangers Cleaning is best achieved by the recirculation method using a heated 20% solution of "Stanrose® Tank Clean HD ". First of all drain off any remaining oil from Heat Exchanger. Connect the discharge side of a portable pump to the lower heat exchanger connection & the suction Side of the pump to the bottom outlet of a 200 litre drum. Complete the circuit by connecting the upper connection on the heat exchanger to the top of the drum. Maintain the bath temperature between 60-80 0 C throughout the cleaning operation. If it is not possible to heat, the operation will need to be extended. Use the pump to maintain circulation for 12 to 15 hours. When the cleaning is completed, disconnect the lower heat exchanger connection and drain out the cleaning solution. Connect a fresh water supply to the upper heat exchanger connection, and rinse until the water runs clean from the lower connection. When rinsing is complete, disconnect the water supply and thoroughly drain and dry the heat exchanger Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® One Shot BWT Stanrose® One Shot BWT is a well-balanced blend of boiler water treatment chemicals designed to protect low pressure auxiliary and fire tube boilers against scale and corrosion. It is liquid compound containing alkaline mineral salts, sequestering agents, scale and corrosion inhibitors and sludge conditioners. Common Name One Shot Product Code STAN-BWT146 Features and Benefits “Stanrose® One Shot BWT ” is designed to achieve the maximum degree of boiler protection with a minimum of chemical testing and feed procedures. The system is designed to meet the operating conditions for the low pressure steam generator not requiring the more sophisticated testing and feed procedures. Technical Properties Form Liquid Appearance Clear Solution Sp. Gravity 1.1 Flash Point None pH Value 13.5 “Stanrose® One Shot BWT ” incorporates all water treatment chemicals in one liquid formulation that can be fed directly from the drum. Recommended Uses Oxygen Scavenger : To chemically react with dissolved oxygen there by preventing oxygen" pitting" corrosion. Synthetic Polymers and Alkalinity Control Agents : To chemically react with scale forming minerals forming a nonadherent sludge easily removed by blowdown. These materials also protect against the adherence of oily deposits introduced by oil contamination. Defamer: A defoamer has been incorporated into the formulation to help in the production of clean steam and to prevent the problems associated with the carryover of solids into steam traps and valve. Method of Application Dosage : “Stanrose® One Shot BWT ” can be fed neat to the boiler or can be diluted to any convenient strength. The treatment can be shot fed to any convenient point in the feed water circuit. As a guideline to establishing control on an untreated boiler, feed 2 litres or 4 pints of treatment per ton of boiler water. Adjust feed from then on in accordance with the periodic alkalinity test procedure. If 'p' Alkalinity is above 400ppm decrease treatment. Test Procedure : “Stanrose® One Shot BWT ” consists of two easy to use portable kits. One to record 'P' Alkalinity which indicates that sufficient treatment has been added and one to record Chlorides to control blowdown. Blowdown : Blowdown the low pressure steam generator one a day. For optimum control over boiler water solids if conditions such as high feed water solids or make-up water requirements are encountered. Handling : “Stanrose® One Shot BWT ” contains alkaline materials and care should be taken avoid contact with skin and eyes. In case of contact, immediately flush skin and eyes with plenty of water for 15 mts. Get medical attention. Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Oxycontrol-S Stanrose® Oxycontrol-S is an oxygen scavenger based on sodium sulphite blended with a specially selected catalyst which will effectively speed up the reaction of the sulphite with dissolved oxygen even at low temperatures. Stanrose® Oxycontrol-S is the ideal oxygen scavenger for all water tube boilers operating below 60 atmospheres(850 psi). Common Name Oxycontrol-S Product Code STAN-BWT150 Features and Benefits Feed solutions should be prepared with a minimum of stirring. This solution can be fed alone or in conjuction with other treatment chemicals not affected bob a reducing agent. Approx. fifty liters of "Stanrose® Oxycontrol-S" will be required to chemically react with one part of dissolved oxygen. , feed solutions should be made up fresh daily. Technical Properties For Dosage refer technical data sheet. Usage of Table : 1. Determine sulphite as ppm SO3 in boiler water by testing. 2. Find sulphite range in the table that contains the measured free sulphite residual ( ppm So3) 3. Read the ml of "Stanrose® Oxycontrol-S" needed per 1000 ltrs ( or per metric ton )under the appropriate pressure column. Recommended Uses Even with most modern deareation equipment, trace amounts of dissolved oxygen are found in the feed water. This dissolved oxygen will react with the boiler metal and the tubes to cause corrosion and subsequent failures. "Stanrose® Oxycontrol-S" was formulated to remove these minute traces of dissolved oxygen. The fast reaction rate of our special binded catalyst makes "Stanrose® Oxycontrol-S" particularly useful in systems where the boiler feed water temperatures are low or in cold water system. It is excellent in use in standby boilers for the prevention of standby corrosion. Method of Application Feed Requirements : Feed solutions should be prepared with a minimum of stirring. This solution can be fed alone or in conjuction with other treatment chemicals not affected bob a reducing agent. Approx. fifty liters of "Stanrose® Oxycontrol-S" will be required to chemically react with one part of dissolved oxygen. , feed solutions should be made up fresh daily. Feeding Method : "Stanrose® Oxycontrol-S" should be fed continuously for best results to the storage section of the deareator or to the make-up tank. This will ensure a residual in the feed water system as well as boiler at all times, even when make-up requirements are higher than normal. Diaphragm or piston type reciprocating positive displacement pump as well as bypass feeders may be used. A floating lid will help to prevent reaction with atmospheric oxygen. Feed systems chemical feed pumps for insoluble matter in the tank, outlet should be above bottom of tank and preferably equipped with fine screen strainer. Control : "Stanrose® Oxycontrol-S" is controlled by the sulphite test .A free residual of 30 to 60 ppm is normally maintained in the boiler water. A standard iodimetric titration is used for checking. These test units are available from your Stanrose service engineer. Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Coolant It is a blend of organic compound along with 3 to 15% benzotriazole is especially useful in preventing cavitation corrosion in high speed coolant pumps having aluminum housing and impellers. This could aid service life. Common Name Coolant Product Code STAN-CLC084 Features and Benefits Protection against cavitation and corrosion Technical Properties Appearance - Clear Liquid Density - 1.096 g/cm3 Product pH - neat 9.5 Corrosive Action - None Recommended Uses At concentration of 10% by volume, "Stanrose® Coolant" affords excellent protection against cavitation and corrosion to all metal and alloys which are used in cooling system, such as aluminium, ferrous and yellow metals. Method of Application The "STAN-2000-018" should be prepared with water that is clean but not too hard. The following types of water are unsuitable: sea water, mixture of sea water and fresh water, salt water and industrial waste water. The analytical values of the water should be within the following limits: Water hardness : 0 - 100 ppm Chloride contents: max 100 ppm Sulphate contents: max 100 ppm The water must be treated by suitable means if it does not fulfill these requirements, i.e. by adding softened, or distilled or deionized water. Excessive sulphate or chloride contents can also be reduced by adding distilled or deionized water. Storage and Handling Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Deck Cleaner This Eco-Safe deck cleaner is just what you need to clean your deck or to prepare it for staining or water sealing. Stanrose® Deck Cleaner not only cleans the wood decking but restores the wood to a "like new" colour tone, removing the grey weathered wood fibers. No chemical odours, non damaging to plants or grass, not harmful for your pets or children this Stanrose® Deck Cleaner is the ultimate deck cleaner. This video below shows you the entire deck cleaning process, the deck in the video is made of expensive mahogany wood, and you will notice how the colour comes back to the mahogany decking. Stanrose® Deck Cleaner works on all types of wood decking. Stanrose® Deck Cleaner will also dissolve old deck stain so that it can be cleaned and re-stained. This product is made from hydrogen peroxide there is no chemical odours or fumes. Stanrose® Deck Cleaner will not harm plants or grass and it’s safe to use over water, it biodegrades very rapidly only hours after use. Stanrose® Deck Cleaner will not harm people or pets; it will not stain other surfaces and is both safe and highly effective Stanrose® Deck Cleaner is formulated to penetrate wood and uses oxygen bubbles to extract debris from the decking so it can be easily cleaned off. Use of Stanrose® Deck Cleaner and a power washer will greatly lengthen the amount of time your deck will remain clean with a great new look that you just worked so hard to provide. Stanrose® Deck Cleaner will remove surface stains caused by mould and mildew. Common Name Deck Cleaner Product Code STAN-CLC107 Features and Benefits You can use our Deck Wash to safely and easily clean your deck and you can rest easy knowing that it won't harm your plants or produce noxious, stinging fumes. If you are having troubles with your composite decking, try our Composite Deck Wash. If you've cleaned your deck and you want to protect it, check out our Sealers and Stains section. Highly concentrated Waterborne Removes waterborne stains from windows Removes light rust and rust stains from painted and wooden surfaces, metals and glass. Does not contain nonylphenol ethoxylates or other estrogenic compounds. Phosphoric acid free Readily biodegradable Easy to rinse off Non-flammable Technical Properties Form Liquid Appearance Light yellow Density 1,2 pH, in 1% sol. 2 Not Compatible Long term exposure may lead to corrosion of mild steel, cast iron, aluminium and alloys, brass, tin or galvanised material. Recommended Uses Use as a cleaner or use before staining or water sealing. Deck Wash is great on mahogany, teak, pine, cedar, pressure treated or any type of wood. Great on decks, fences, docks, furniture, or any exterior wood surface. Method of Application Coverage Every 2lbs of product will clean 600-800 sq. ft. Directions Add 1⁄2 cup per gallon of water, mix well, stirring frequently, allow the solution to fully activate for 15 minutes prior to use. Apply product with "garden-style" pump sprayer or mop, scrub with brush, keep area moist with product while brushing and rinse with water. For top "professional" results and for decks that haven't been cleaned for a long time use a pressure washer instead of scrub brush and hose. Storage and Handling Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Vaptreat Stanrose® Vaptreat is a concentrated liquid blend of polymer and antifoam agents for controlling scale and foam in evaporators. Stanrose® Vaptreat is Approved by the Norwegian National Institute of Public Health for application in evaporator systems that are used to produce potable water. Common Name Vapour Treatment Product Code STAN-SSC209 Features and Benefits Stanrose® Vaptreat prevents scale by crystal distortion, dispersion, and absorption of scale forming minerals. Crystal distortion As soluble minerals are forced out of solution during evaporation hey go through an intermediate crystal stage before forming dense deposits. Stanrose® Vaptreat reacts with the crystals causing them to be distorted and irregularly shaped. The distorted crystals do not form dense and uniform deposits which would adhere to evaporator surfaces. Ensures that the evaporator works at maximum efficiency by keeping heat transfer surfaces free of scale The antifoaming properties ensure that distillate quality is high as carry over is eliminated Will gradually remove existing scale when dosed at twice the normal rate Concentrated, safe liquid, easy and economical dosing Technical Properties Appearance pale yellow liquid Flash Point none PH of 1% solution 9.2 Specific Gravity 1.09 Recommended Uses Stanrose® Vaptreat should be fed continuously to the evaporator inlet line. Stanrose® Vaptreat can be diluted with fresh water and the feed solution introduced with an eductor or an positive displacement metering ppm. Method of Application The specially selected polymers in Stanrose® Vaptreat combined with the potential scale forming salts in the brine to prevent them from adhering to heat transfer surfaces. These solids are held in suspension and removed with the evaporator brine. The operating efficiency of the plant is maintained for maximum water production. The intervals between cleaning are greatly increased. The product to use for acid cleaning is Stanrose® Descaler, which will remove old scale prior to treatment with Stanrose® Vaptreat . Evaporators have a tendency to produce foam while operating - the de-foaming properties of Stanrose® Vaptreat will stop this foaming and carry-over will be eliminated. Distilled water quality is maintained. Dosing Method The standard dosage, applicable to the majority of systems, is 15-30 ml of Stanrose® Vaptreat per ton of distillate produced. This is based on the rated production capacity of the evaporator. Example: In a 25 ton/day evaporator. Treatment used = 25 x 30 ml = 750 ml of Stanrose® Vaptreat per day. Setting the Flow Rate The treatment is added to the dosage tank and mixed with water. Example: With the 0.75 litres of Stanrose® Vaptreat add sufficient water to make up 50 litres of liquid. Flow rate calculation: Flowrate = 50 Litres/24 x 60= 35 ml/min setting This will last 24 hours. A metering pump can also be supplied for use with Stanrose® Vaptreat if required. N.B. The brine density should not exceed 1.038 g/cm3. The scaling potential increases rapidly over this level. An increase in the amount of Stanrose® Vaptreat used will assist in retaining potential scale forming salts in suspension. For example: If the density rises to 1.050 g/cm3 the dosage should be 60 ml/ton of rated capacity. Dosage : The recommended dosage rate for Stanrose® Vaptreat is 5 to 10 ppm based on type, usage and operating conditions of the evaporator. Your Stanrose® service engineer will readily guide you on the correct dosage. It is preferred that the evaporator be clean and free of deposits before Stanrose® Vaptreat is introduced . Stanrose® Vaptreat will clean up moderate amount of existing deposits. Double the dosage rates previously recommended during the clean up period. Storage and Handling No special precautions required. Use the same care as in handling other chemicals used for maintenance. Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File