Search Results

Staroxy 102 SF Solventfree Epoxy Primer Description Staroxy 102 SF is a two-component amine cured solvent free epoxy coating. It is transparent. It ensures very good adhesion on most concrete floors in atmospheric environments only. Specially designed for high build floor coatings on properly prepared concrete floor substrates. Uses Designed for a wide range of floors with various levels of mechanical and chemical exposure. It is a primer for all Stanrose surface coating products. Specially designed for use with the traffic deck system for heavy duty traffic, areas such as ramps, car parks, parking bays, pedestrian walkways, roof decks and industrial floors. Recommended for cold stores, laboratories, hospitals, food and beverage plants, kitchens, high tech manufacturing facilities, dairies, warehouses, factories and hangars. This product when used with Stanrose Deck Guard (Antiskid) Aggregates, is suitable for filling and repairing of cracks, undulations and surface imperfections. Advantages • Simple application. • Excellent anchoring to the surface • Provides high tensile and impact strength. • Heat and frost resistant • Stops the creation of dust. • Vapor block • Chemical resistant Technical Properties • Colour: Clear • Gloss: Glossy • Solid contents (% by volume) 99 ± 1% • Recommended DFT/ Coat: 150 microns • Drying Time Surface Dry: 4 hours • Hard Dry: 20 hours • Mixing Ratio: Resin (2) : Hardner (1) by volume/weight • Pot life at 25°C: 25 minutes • Recommended Coverage: 5m2 per Kg for 150 microns. • Water Absorption (%w/w): Nil • Specific Gravity 1.00- 1.05(mixed) All data is valid for mixed material. • Adhesion to Concrete: >2 N/mm2 (concrete failure) ASTM D 903 • Hardness (SHORE D Scale) > 70 ASTM D 2240 • Resistance to Water Pressure No Leak (1m water column, 24h) DIN EN 1928 Directions for Use Substrate Requirements: • To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. Substrates Temperatures must be a minimum of 55-60°F. and a maximum of 85°F. • Laitance deposits are best removed by Planetary diamond disc grinder or by captive blasting followed by vacuum cleaning to remove dust debris. • Substrate must be clean and free of Dirt, waxes, curing agents and any other foreign material that will interfere with bonding. Surface preparation: Remove oil, grease and any other contaminants using thinner. Blast clean to minimum Sa 2½ (Swedish standard SIS 05 5900). If blasting is not practically possible, make full use of mechanical tools to remove loose rust and scale to St.2 Swedish standard. Surface should be clean and dry before application of Staroxy 101 SB. New concrete or cementitious substrates should have been placed at least 28 days and have a moisture content of less than 5% before topping with Staroxy 102 SF. After surface is dry, all repair work like sealing of joints, crack filling of cavities and crevices should be carried out. If the surface is Tremix or smooth surface then Shot Blasting is carried out to make the surface rough in order to enhance the bonding of the primer. Concrete defects such as voids, bug holes, excess porosity, and physical and chemical damage are usually filled or repaired prior to the installation of the F/C system. (Materials such as slurries, mortars, and polymer concrete are used to level, smooth and patch concrete surfaces. The laitance (A thin, weak, brittle layer of cement and aggregate on concrete surface) on in-situ bases and any surface sealer or curing membrane should be entirely removed by suitable mechanized equipment, e.g. shot- blasting, panning or grinding, to expose cleanly the coarse aggregate Mixing and Application: 1. Pack components are pre-weighed for optimum performance. Never split packs. 2. Stir resin thoroughly and then mix two parts of resin with one part of hardener by volume. Empty contents of Resin into a mixing container and pre-mix to assure the suspension of solids. Stir resin thoroughly and then mix two parts of resin with one part of hardener by volume. 3. Add Hardner and continue to mix to a uniform consistency for 1-2 minutes. 4. Mix with slow speed drill or manually depending on the quantity in mixing bucket and helical spinner head for 2 minutes. 5. Spread the mixture on the floor immediately and allow it to dry for 4 hours. 6. Primer is normally spread with a brush, floor squeegee or roller and back-rolled with a 3/8" medium nap roller. Care should be taken to minimize the entrapment of air caused by over rolling. Method of Application Primer is normally spread with a brush, floor squeegee or roller and back-rolled with a 3/8" medium nap roller. Care should be taken to minimize the entrapment of air caused by over rolling. Packaging Size, Storage and Shelf Life Available in 3 Kg, 6 Kg, 15 Kg, 60 Kg, 200 kg packs and has a maximum shelf life of 12 months in the un-opened containers. The product should be stored in accordance with national regulations. It should be kept in a cool, well-ventilated area, away from heat, direct sunlight, sparks and children. Handle with care. It has a shelf life of 12 months from the date of manufacturing.

Staroxy 103 MOT Moisture and Oil Tolerant Solvent Free Epoxy Primer Description Staroxy 103 MOT is a two-component, moisture-tolerant epoxy primer for steel, concrete and other substrates as specified. It is used to prime concrete, steel and other substrates prior to application of other Staroxy Coatings, linings, membranes, sealants and polymer concretes. It achieves a tenacious bond to the substrate and tolerates substrate dampness but not wet surfaces. Staroxy 103 MOT is a two-component amine cured solvent free epoxy coating. It is transparent. It ensures very good adhesion on most concrete floors in atmospheric environments only. Specially designed for high build floor coatings on properly prepared concrete floor substrates. Uses Designed for a wide range of floors with various levels of mechanical and chemical exposure. It is a primer for all Stanrose surface coating products. Specially designed for use with the traffic deck system for heavy duty traffic, areas such as ramps, car parks, parking bays, pedestrian walkways, roof decks and industrial floors. Recommended for cold stores, laboratories, hospitals, food and beverage plants, kitchens, high tech manufacturing facilities, dairies, warehouses, factories and hangars. This product when used with Stanrose Deck Guard (Antiskid) Aggregates, is suitable for filling and repairing of cracks, undulations and surface imperfections. Staroxy 103 MOT is used as a primer for other materials in a wide variety of applications. Typical applications include: • Secondary containment linings • Tank linings • Monolithic floor toppings • In-situ polymer concrete installations • Trench linings Advantages • Simple application. • Excellent anchoring to the surface • Provides high tensile and impact strength. • Heat and frost resistant • Stops the creation of dust. • Vapor block • Chemical resistant Technical Properties • Colour: Clear • Gloss: Glossy • Solid contents (% by volume) 99 ± 1% • Recommended DFT/ Coat: 150 microns • Drying Time Surface Dry: 4 hours • Hard Dry: 20 hours • Mixing Ratio: Resin (2) : Hardner (1) by volume • Pot life at 25°C: 25 minutes • Coverage: 5-10m2 per Kg • Water Absorption (%w/w): Nil • Specific Gravity 1.00- 1.05 (mixed) All data is valid for mixed material. • Adhesion to Concrete: >2 N/mm2 (concrete failure) ASTM D 903 • Hardness (SHORE D Scale) > 70 ASTM D 2240 • Resistance to Water Pressure No Leak (1m water column, 24h) DIN EN 1928 Directions for Use Substrate Requirements: • To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. Substrates Temperatures must be a minimum of 55-60°F. and a maximum of 85°F. • Laitance deposits are best removed by Planetary diamond disc grinder or by captive blasting followed by vacuum cleaning to remove dust debris. • Substrate must be clean and free of Dirt, waxes, curing agents and any other foreign material that will interfere with bonding. Surface preparation: Remove oil, grease and any other contaminants using thinner. Blast clean to minimum Sa 2½ (Swedish standard SIS 05 5900). If blasting is not practically possible, make full use of mechanical tools to remove loose rust and scale to St.2 Swedish standard. Surface should be clean and dry before application of Staroxy 103 MOT. New concrete or cementitious substrates should have been placed at least 28 days and have a moisture content of less than 5% before topping with Staroxy 103 MOT. After surface is dry, all repair work like sealing of joints, crack filling of cavities and crevices should be carried out. If the surface is Tremix or smooth surface then Shot Blasting is carried out to make the surface rough in order to enhance the bonding of the primer. Concrete defects such as voids, bug holes, excess porosity, and physical and chemical damage are usually filled or repaired prior to the installation of the F/C system. (Materials such as slurries, mortars, and polymer concrete are used to level, smooth and patch concrete surfaces. The laitance (A thin, weak, brittle layer of cement and aggregate on concrete surface) on in-situ bases and any surface sealer or curing membrane should be entirely removed by suitable mechanized equipment, e.g. shot- blasting, panning or grinding, to expose cleanly the coarse aggregate Mixing and Application: 1. Pack components are pre-weighed for optimum performance. Never split packs. 2. Stir resin thoroughly and then mix two parts of resin with one part of hardener by volume. Empty contents of Resin into a mixing container and pre-mix to assure the suspension of solids. Stir resin thoroughly and then mix two parts of resin with one part of hardener by volume. 3. Add Hardner and continue to mix to a uniform consistency for 1-2 minutes. 4. Mix with slow speed drill or manually depending on the quantity in mixing bucket and helical spinner head for 2 minutes. 5. Spread the mixture on the floor immediately and allow it to dry for 4 hours. Method of Application Primer is normally spread with a brush, floor squeegee or roller and back-rolled with a 3/8" medium nap roller. Care should be taken to minimize the entrapment of air caused by over rolling. Packaging Size, Storage and Shelf Life The product should be stored in accordance with national regulations. It should be kept in a cool, well-ventilated area, away from heat, direct sunlight, sparks and children. Handle with care. It has a shelf life of 12 months from the date of manufacturing. Available in 3 Kg, 6 Kg, 15 Kg, 60 Kg packs and has a maximum shelf life of 12 months in the un-opened containers.

Marine Care Cleaning Chemicals Stanrose® BETA – HD Nuclear DC Chemical BETA – HD Nuclear DC Chemical is a heavy duty cleaner mainly designed for cleaning of nuclear contamination. It provides excellent result for degreasing of oil, soil, grease etc. It is very effective for decontamination of nuclear contaminated equipments, nuclear contaminated cloths, tools, floors, glass, wall etc. It is non flammable, bio degradable, non toxic, colorless, low foam, eco friendly, stable liquid advisable for cleaning of even very heavy contamination. Recommended for nuclear, pharma, chemical, textile industries. More ​ ​ More Stanrose® Stanpol-B-300 Stanrose® Stanpol-B-300 Toilet cleaner prevents the build-up of stains in the toilet bowl and keeps it visibly clean with effective removal of germs in the toilet More Stanrose® Degreaser - M Stanrose® Degreaser-M is an Environmentally Sensible, heavy duty, non-flammable, non-hazardous, mildly alkaline aqueous carbon remover and degreaser. The product carries a complete corrosion Inhibition package and rinse aid technology. Formulated specifically for cleaning stainless steel, carbon steel, aluminum alloys and all other ferrous and non ferrous metals. Cleans all Types of soils including sulphur based cutting fluids, adhesives, carbon, dirt, oils, grinding, finishing & polishing compounds, water & solvent based inks Carbon, Dirt, Cutting Fluids. More Stanrose® Multi Clean A multi-purpose concentrated cleaner/degreaser precisely formulated for industry; removes stubborn soils, greases, oils, sludge, and soot. Stanrose® Multi Clean is a cleaner, degreaser and disinfectant developed for the automotive, industrial, military and domestic marketplace. The unique formula contains technology that weakens a soil’s ability to cling to surfaces and lifts soils and traps them in a tiny bubble known as a micelle to be rinsed away. Stanrose® Multi Clean is a water based formula that is VOC compliant in all 50 states and contains no petroleum or chlorinated solvents. More Stanrose® One Shot BWT Stanrose® One Shot BWT is a well-balanced blend of boiler water treatment chemicals designed to protect low pressure auxiliary and fire tube boilers against scale and corrosion. It is liquid compound containing alkaline mineral salts, sequestering agents, scale and corrosion inhibitors and sludge conditioners. More Stanrose® Seacare OSD-III Dispersants are chemicals that are applied directly to an oil slick. The key components of chemicals dispersants are surface active agents called Surfactants. Stanrose® Seacare OSD-III assists with breaking up the slick into small droplets ranging in size a few micrometers to few millimetres. Chemical dispersants can do this because they contain molecules that are both water compatible and oil compatible. The molecules align themselves around the oil droplets break away from the slick. The Action prevents the coalescence (reforming or joining) of oil droplets. So, the oil can no longer form slick on water surface, and it reduces the adherence of the oil to solid particles ( sand ) and hard surfaces ( sea walls & boat hulls )Chemical dispersants remove the oil from the surface of the water and into the water column. Once in the water column, the oil is diluted to less harmful levels, and eventually is used as a food by bacteria. By removing the oil from the water surface, birds, marine mammals and sensitive coast is protected. More Stanrose® Seacare OSD-II Dispersants are specially designed oil spill products that are composed of detergent‐like surfactants in low toxicity solvents. Dispersants do not remove oil from the water, but instead break the oil slick into small droplets. These droplets disperse into the water and are further broken down by nature. Dispersants also prevent the oil droplets from coming back together and forming another surface slick. Dispersed oil droplets are less likely to stick to birds and other animals, shoreline rocks, and vegetation. More Stanrose® Seacare OSD-I Stanrose® Seacare OSD-I” is a biodegradable hydrocarbon based product with high dispersing efficiency and low toxicity. It is approved as a Type I dispersant according to LR448 specifications by the Department for Environment, Food & Rural Affairs (DEFRA) formerly the UK Ministry of Agriculture, Fisheries and Food (MAFF). More Stanrose® Oxalwash Stanrose® Oxalwash is a 100% super concentrated powder so you can safely dilute it to suit your cleaning task. It is a much safer option than most other acids used in cleaning including Hydrochloric and Hydrofluoric Acid. More Stanrose® Oxycontrol-H When operating modern boiler facilities even under ideal conditions, trace quantities of oxygen are left in the feed water despite mechanical de-aeration. More Stanrose® Oxycontrol-S Stanrose® Oxycontrol-S is an oxygen scavenger based on sodium sulphite blended with a specially selected catalyst which will effectively speed up the reaction of the sulphite with dissolved oxygen even at low temperatures. Stanrose® Oxycontrol-S is the ideal oxygen scavenger for all water tube boilers operating below 60 atmospheres(850 psi). More Stanrose® Paint Remover A fluffy, thick jelly like stripping compound based on non-flammable solvents, to soften, dissolve and remove dry old paint layers. It can remove air drying alkyd paints, stoving paints and water based paints effectively. It can also remove two component polyurethane, epoxy and other coatings with applications in extended times. It has good penetration properties and allows quick removal of paint without any considerable damage to the substrate. More Stanrose® SPOL "Stanrose® SPOL" is a pH-neutral, liquid concentrated detergent with good cleaning qualities. It is multi- purpose heavy duty cleaning soap solution used as a common dirt remover in residential, commercial and industrial cleaning processes. It contains effective but mild and environmentally safe wetting agents and surfactants that allow rapid penetration to remove fats and oils. "Stanrose® SPOL" is especially suitable for hydrocarbon freeing of tanks, and is safe on all tank coatings including zinc silicate. More Stanrose® Tank Clean - Brite Stanrose® Tank Clean HD is a micro emulsion water based tank cleaner. This product is low toxic, biodegradable and safe to use. It contains natural solvents linked with easily biodegradable surfactants. Main application is for hydrocarbon freeing but it may also be used for other tank cleaning purposes where a strong degreasing effect is required. More Stanrose® Tank Clean - Brite It is concentrated acidic cleaner containing phosphoric acid and non-ionic surfactants. Tankleen Bright is formulated for effective removal of white residues from epoxy-coatings remaining after carriage of fatty acids as well as stains removal and to upgrade coated cargo tanks. More Stanrose® Tolune Toluene is a fragrant compound of hydrogen and carbon (hydrocarbon), it is clear in colour with an odour similar to paint thinners, probably because most paint thinners contain Toluene around 30%. More Stanrose® Vaptreat Stanrose® Vaptreat is a concentrated liquid blend of polymer and antifoam agents for controlling scale and foam in evaporators. Stanrose® Vaptreat is Approved by the Norwegian National Institute of Public Health for application in evaporator systems that are used to produce potable water. More Stanrose® Waterless Hand Wash It is a milky white creamy gel containing natural ingredients, moisturisers, surfactants, and powerful dispersing agents. This is a better substitute to petroleum products & caustic based detergents which drain the body oil. Only 2 to 5 grams sufficient to clean most greasy hand. More Stanrose® Alky Control This liquid additive is a hydroxide alkalinity builder and sludge conditioner designed to increase alkalinity in conjunction with other steam boiler treatments. It enhances the corrosion inhibition and improves the properties of other boiler water products by helping to stabilize the pH within a boiler. It can be used on a "one-shot" application basis, or with an automated continuous feed system, and is safe to use with other boiler treatment chemicals. More Stanrose® 3-in-1 Rust Cleaner Stanrose® 3-in-1 Rust Cleaner is an incredibly versatile product which acts as a light duty lubricant, penetrant/release agent, dewatering fluid and corrosion preventative. Stanrose® 3-in-1 Rust Cleaner contains a blend of cleaning solvents to wash away residues of oil and grease, dispelling water and allowing deep penetration into threads and mechanisms. A combination of mineral oils and oxidised waxes provide lubrication and unrivalled corrosion protection. In aggressive accelerated salt spray tests Stanrose® 3-in-1 Rust Cleaner has been shown to provide up to 3 times the protection of rival products. More Stanrose® AC Cleaner “Stanrose® AC Cleaner” is a powerful solvent emulsion cleaner for the cleaning of diesel engine air coolers, scavenging air systems and compressor sides of turbochargers. More Stanrose® AC Cleaner Plus “STANROSE® AC CLEANER PLUS” is a powerful cleaning agent for cleaning of diesel engine air coolers, scavenging air systems and the compressor side of turbochargers. “STANROSE® AC CLEANER PLUS” is a micro-emulsion type cleaner, where a synergistic blend of biodegradable surfactants and low toxicity solvents replace the use of the harmful solvents traditionally used in air cooler cleaners without reducing the cleaning performance. It is formulated to meet the latest environmental standards, and is non toxic both to the environment and to persons handling it. “STANROSE® AC CLEANER PLUS” contains no chlorinated or aromatic hydrocarbon solvents, nonylphenol ethoxylates or other substances harmful to the environment. More Stanrose® Alkaline Cleaner HD Stanrose® Alkaline Cleaner HD is a high performance, heavy duty alkaline cleaner and detergent available in a liquid concentrate form. It is scientifically formulated for use in soak tanks, high pressure washers, automated scrubbing machines as well as for manual application. Stanrose® Alkaline Cleaner HD is specially formulated from a blend of soaps, synthetic detergent, solvents and inorganic alkaline builders and comes in a highly concentrated form. This product is an extremely versatile heavy duty industrial cleaner developed specifically for use in automated scrubbing machines, high pressure washers, soak tanks as well as for manual use. More Stanrose® Clean Care Alkaline Non-caustic water based alkaline cleaner, containing corrosion inhibitors to prevent the corrosion of metals such as zinc, aluminium, copper, brass and tin. "STANROSE® CLEAN CARE ALKALINE" minimizes the hazards in handling caustic based materials. More Stanrose® Bio Guard “Stanrose® Bio Guard” is a very effective clear , yellowish green with , anti fungal based dispersing cleaner for the control of fouling by marine growth such as algae, shellfish, mussels, barnacles and micro-organisms and fungal growth in the sea water side of cooling systems. Due to its molecular firm foaming properties, it also acts as a corrosion inhibitor. It should be preferably be started on a clean system since it is formulated to prevent growth rather than remove existing growth of micro-organism bacteria , fungi , larvae etc. More Stanrose® Aqua Degreaser "STANROSE® AQUA DEGREASER" is mixture of Emulsifier, new technology surfactants (With high solvency and emulsification effect), Corrosion inhibitors, Rust preventive. due to free from caustic and Hydrocarbon very gentle on hands & ideal for cleaning Walls Wood works, Metals and all areas. Acts as superior quality cleaner / degreaser. "STANROSE® AQUA DEGREASER" containing corrosion inhibitors to prevents the corrosion of metals such as Aluminium, Copper, Brass and Tin. "STANROSE® AQUA DEGREASER" is designed to clean Animal / Vegetables oils, Fats, Hydrocarbon removes Dirt, Iink, Carbonized grease, Oil, Heavy oils etc. Specialized for all types of cleaning and degreasing may be applied by brush, hand spray or used in ultrasonic cleaning tanks, immersion soak tanks and high and low pressure spray appliances. May be used neat or diluted by up to 50 parts of water according to the amount and type of soil to be Removed. More Stanrose® Aquatuff HF "Stanrose® Aqua HF " is a heavy duty alkaline cleaner with good foaming qualities specially formulated for cleaning cargo holds on bulk carriers and OBOs. The dense foam created prevents the cleaning solution from running off vertical surfaces and thereby enhances the cleaning efficiency. It is water based and is safe to the environment, containing only biodegradable ingredients. It effectively removes most dry cargoes to “water white standard” " Stanrose® Aqua HF " is specially developed for cargo hold cleaning. But may also be used for other cleaning applications where " Stanrose® Aqua HF " normally is used and where high foam is beneficial. More Stanrose® Biocide “Stanrose® Biocide” is a liquid, pumpable algicide dispersion for water-based technical products. Due to the very low water solubility it is especially recommended for coating exposed to severe weathering. “Stanrose® Biocide” controls algal growth on paints and plasters on the exterior of buildings and so enhancing their aesthetic appearance. More Stanrose® Bio-Degreaser HP Stanrose® Bio Degeaser - HP is a non-emulsifying degreaser based on a blend of high boiling hydrocarbons and surfaceactive components. It is suited to remove most mineral oils, greases and preserving agents. Safe to use on most metals. Undiluted at a temperature of ± 20 °C it can also be used on most synthetics, paints, lacquers, epoxy and zinc silicate coatings. More Stanrose® Bio Degreaser “Stanrose® Bio Degreaser” is a non-emulsifying degreaser based on a blend of high boiling hydrocarbons and surfaceactive components. It is suited to remove most mineral oils, greases and preserving agents. Safe to use on most metals. Undiluted at a temperature of ± 20 °C it can also be used on most synthetics, paints, lacquers, epoxy and zinc silicate coatings. More Stanrose® Anti-Fouling Stanrose® Anti-Fouling is a very effective clear , yellowish green with anti fungal based dispersing cleaner for the control of fouling by marine growth such as algae, shellfish, mussels, barnacles and micro-organisms and fungal growth in the sea water side of cooling systems. Due to its molecular firm foaming properties, it also acts as a corrosion inhibitor. More Stanrose® BTC Stanrose® BTC is a biological product which has been specially formulated for the removal of stains and deposits on urinals and toilets. Stanrose® BTC can also be used in waterless urinal systems. It also helps reduce or eliminate odours associated with these systems. Stanrose® BTC is safe to use in Septic Tank Installations where the use of nasty chemicals is not advised. Stanrose® BTC is a completely natural toilet cleaner which is made of no hazardous chemicals and only naturally occurring bacterial products combined. This combined product is an excellent toilet cleaner and will leave a fresh clean smell. TECHNICAL INFORMATION Stanrose® BTC contains a blend of selected micro-organisms in a liquid formulation. These micro-organisms have been specially selected as being naturally occurring and for their ability to grow and produce a wide range of enzymes which help to degrade organic waste materials. Stanrose® BTC also contains a blend of surfactants designed to enhance the cleaning effect of the product and also to penetrate into deposits on surfaces. This also aids the microbial action by making a greater surface area available for microbial attack. All aspects of the formulation help to remove organic materials and prevent build up of deposits which can lead to off odours in toilets and urinals. This action helps to mobilise the organic material and transport it to the wastewater treatment plant where it can be properly treated. The chemical ingredients of the product are biodegradable so will not have an adverse effect on the operation of an effluent treatment plant. More Stanrose® BWT Coagulant Stanrose® BWT Coagulant prevents the formation of deposits on boiler internal surfaces. Sludge is kept dispersed in small particles and conditioned to be removed by normal blowdown. In this way tube overheating due to deposits is avoided. The product is a liquid so is easy to feed to the affected area. The treatment is primarily used in conjunction with Hardness Control, but also with other Stanrose® chemical treatments. Stanrose® BWT Coagulant can also be used where minor oil contamination has been experienced, the oil being required to be coagulated for removal by blowdown. More Stanrose®Carbon Remover It is a non-corrosive, powerful micro emulsion based cleaner for removal of carbonaceous deposits. It contains no chlorinated solvents or phenolic compounds and has low toxicity to the environment and to persons handling it. More Stanrose® Carpet Shampoo Stanrose® Carpet Shampoo is a clear light green liquid that quickly and easily eliminates stains and malodors wherever they occur. It settles into fabrics depositing its minuscule encapsulating molecules that absorb unpleasant odours trapped in carpets, rugs and upholstery and also deposit its odour encapsulating blend that eliminates bad odours; the biodegradable surfactants and solvents present in Stanrose® Carpet Shampoo then cleans and pick up all soil and dirt for a perfect cleaning job. This product can be used on any fabric, however test an inconspicuous area before to make sure there is no change in appearance. More Stanrose® Cement Remover Stanrose® Cement Remover is designed to instantly penetrate and disperse cement, providing complete cleaning of cement cargo deposits, dry cement stains and lime deposits. The product is capable of cleaning hard cement deposits perfectly while removing the possible existing rust. Stanrose® Cement Remover is water based and non-flammable containing powerful acids, inhibitors for surface protection and efficient detergents. More Stanrose® Gum Remover “Stanrose® Gum Remover” is designed to soften and remove residues of chewing gum from floors, carpets, and upholstery. Rapidly lifts chewing gum from carpets and porous surfaces without the need for damaging freeze sprays Use as supplied Suitable for use on most carpets and upholstery within schools, hospitals, leisure complexes and other public areas Heavy duty performance even on old and trodden-in gum Citrus fragrance More Stanrose® Chlorine Tab Stanrose® Chlorinating Tablet is a dry organic chlorine in tablet form giving a high available chlorine base, ensuring an effective sterilising and disinfecting action in slow release form. 200g tablet with 90-92% available chlorine. For chlorination of swimming pools, sewage and waste water.Standard tablet size: 75 mm diameter - 25 mm H. For swimming pool water treatment: 4 large tablets every 100 m3 of water to be put in skimmers or in floating trays. For waste water treatment, fill the chlorinating pipes until 2 to 5 PPM of residual active chlorine are obtained. If below 2 PPM, use both chlorinating pipes. More Stanrose® PWD Combitreat Stanrose® PWD Combitreat is a dry powder compound containing alkaline mineral salts, sequestering agents, scale and corrosion inhibitors and scale conditioners. More Stanrose®Control C Product Description : “Stanrose® Control C” is a concentrated liquid neutralizing agent for corrosion control in condensate and feed water systems. Technical Review : Carbon dioxide enters the condensate system in two ways :- (a) As a dissolved gas. (b) As a decomposition product of soluble carbonates and bicarbonates , carbon dioxide vaporizes from the boiler and forms carbonic acid when it condenses with the condensate lowering the pH, iron and copper will enter into solution more rapidly as pH decreases causing an increase in corrosion rate. Within the condensate system and deposition of metallic oxides in the boiler “Stanrose® Control C” is quickly volatilised in the boiler and travels with the stream. In this way, it is able to neutralize carbon dioxide at all points through out the system, “Stanrose® Control C” effectively protects condensate areas against grooving or channeling and prevents the frequent failure at threaded points caused by low pH attack. More Stanrose® Coolant It is a blend of organic compound along with 3 to 15% benzotriazole is especially useful in preventing cavitation corrosion in high speed coolant pumps having aluminum housing and impellers. This could aid service life. More Stanrose® Corrosion Inhibitor A corrosion inhibitor is a substance when added in a small concentration to an environment reduces the corrosion rate of a metal exposed to that environment. Inhibitors often play an important role in the oil extraction and processing industries where they have always been considered to be the first line of defence against corrosion. More Stanrose® Biostan Oil Cleaner "Stanrose® Biostan Oil Cleaner" is a very strong cleaner, which can be used to soften up / remove baked on drying oils and used after animal and vegetable oils, fish oils, tall oils, tug oils etc .It is low toxic product with an exceptional solvency power on soil & oily matter. It is free from hydrocarbon solvents, Biodegradable minimizes the extreme hazards to personnel in handling materials. More Stanrose® Deck Cleaner This Eco-Safe deck cleaner is just what you need to clean your deck or to prepare it for staining or water sealing. Stanrose® Deck Cleaner not only cleans the wood decking but restores the wood to a "like new" colour tone, removing the grey weathered wood fibers. No chemical odours, non damaging to plants or grass, not harmful for your pets or children this Stanrose® Deck Cleaner is the ultimate deck cleaner. This video below shows you the entire deck cleaning process, the deck in the video is made of expensive mahogany wood, and you will notice how the colour comes back to the mahogany decking. Stanrose® Deck Cleaner works on all types of wood decking. Stanrose® Deck Cleaner will also dissolve old deck stain so that it can be cleaned and re-stained. This product is made from hydrogen peroxide there is no chemical odours or fumes. Stanrose® Deck Cleaner will not harm plants or grass and it’s safe to use over water, it biodegrades very rapidly only hours after use. Stanrose® Deck Cleaner will not harm people or pets; it will not stain other surfaces and is both safe and highly effective Stanrose® Deck Cleaner is formulated to penetrate wood and uses oxygen bubbles to extract debris from the decking so it can be easily cleaned off. Use of Stanrose® Deck Cleaner and a power washer will greatly lengthen the amount of time your deck will remain clean with a great new look that you just worked so hard to provide. Stanrose® Deck Cleaner will remove surface stains caused by mould and mildew. More Stanrose® Deflame Electrosolv Stanrose® Deflame Electrosolv is a fast evaporating cleaner that leaves no residue. The product is suited for cleaning electrical and electronic devices. The product is used as an electrical contact cleaner to remove grease, dirt, oil, flux and other surface contaminants from sensitive electrical/electronics devices. Stanrose® Deflame Electrosolv can also be used to clean motorized instruments, control panels, electrically driven equipment, motors and other electronic devices requiring non-flammable, low residue degreasing agents. More Stanrose® Liquid Descaler A fully inhibited, fast acting descaler. More Stanrose® DI Water Stanrose® DI Water is simply water that has had most of the mineral content and dissolved ion content removed. It is pure water. The cleanliness of the water is rated as its resistance value. [Pure water will not conduct electricity][The rating is in Meg Ohms. Microsiemmens or Conductivity is also used as a measurement of DI water Standard tap water is brought to a temperature of about 72 degrees f and run though a pre filter system consisting of a 25 micron sediment filter, 25 micron carbon filter and either a water softener filter or a chloramines filter [depending on your particular water quality and your local government treatment method] and then the main DI system consisting .5-micron filter to remove particulates, a carbon filter then removes any organics within the water. A reverse osmosis filter removes further contaminants and a mixed bed resin filter removes the final dissolved minerals. This is a very basic process for production of DI water on a small scale. Larger systems are very complicated and use pumps and re- circulation loops to provide larger volumes of DI water. More Stanrose® Diesel Guard Stanrose® Diesel Guard is a dry powder, nitrite/borate based compound with unique formulation with organic Corrosion Inhibitors, Anti- Scalant for use in closed cooling water systems , for preventing corrosion and scale formation in Internal combustion engines, compressor cooling system, DG - set at high or low temperature. It is also acts as a corrosion inhibitor (Protects all the metals including cast iron, mild steel , copper). The stable oxide film that is formed by Stanrose® Diesel Guard prevents corrosion caused by electrolytic action between dissimilar metals used in the system . Stanrose® Diesel Guard has been field tested and found to have no detrimental effects on non metallic substances such as seals, glands, packing, hoses, gaskets etc., normally used in these' systems. More Stanrose® Dieslite Stanrose® Dieslite is a catalytic combustion improver which permits the burning of lower cost residual fuel oils. More Stanrose® Easy Dish Clean The OH eco-friendly liquid dish soap is fragrance free, dye free, phosphate free and formaldehyde free. More Stanrose® Drain Cleaner Stanrose® Drain Cleaner, enzyme free biological drain cleaner, opener and maintainer, is the latest development in the natural, biological treatment of grease laden drain systems. This select multiple strain synergistic blend of bacteria is specifically designed to go to work to provide rapid penetration, breakdown and degradation of organic deposits and blockages found throughout drain systems. Stanrose® Drain Cleaner also effectively counteracts odours often caused by organic build-ups within the drain system while penetrating to attack and digest grease and waste thus eliminating the source of the odours. More Stanrose® Dual Purpose Stanrose® Dual Purpose is a specially formulated blend of organic dispersing agents, water displacing surfactants and combustion catalysts. This product is designed to meet two objectives: 1. Improve the precombustion characteristics of light and heavy fuels. 2. Introduce combustion catalysts into the combustion zone to improve combustion efficiency and minimize fireside corrosion and deposit problems. More Stanrose® Electriclean The Stanrose® Electriclean, is an electric motor and machinery cleaner, designed to clean and degrease in-place running electric motors. It is a non-corrosive, no flash point, high dielectric strength and powerful cleaning solution capable of ridding dirt, grime, grease and oil off metal electric motor components, including precision parts, rollers, elevator shafts, control points, bearings, coils and rotors. Leaving no residue and containing no CFCs or trichloroethylene, the Stanrose® Electriclean is also clean and safe to use. Rigorously tested to ensure performance is up to mark, it is a handy tool suitable for use in places where electric machinery sees extensive use and the cleaning of electric components are vital to maintain smooth operation, such as manufacturing plants, printing plants, garages, automotive repair shops, office buildings, hospitals, restaurants, schools. More Stanrose® Electrosolve Slow Dry Stanrose® Electrosolv Slow Dry are cold degreasing safety solvents. They combine the best cleaning - qualities of the inflamable solvents and carbon tetra chloride, but eliminate the explosive and toxic dangers of these products. They are designed for degreasing and cleaning electrical equipments such as motors and generators, circuit breakers, distribution panels, machinery, instruments, etc. Additionally these cleaners are very effective for removing dust particulars and oils where water washing is cumbesome, messy, troublesome or rust promoting. More Stanrose® Electrosolv Stanrose® Electrosolv is an excellent Electric Parts cleaneing solvent. It is a perfect blend of non-chlorinated degresol with surfactants which help in degreasing and cleaning electrical equipments. The application of this product is very easy and it can be used for all electrical equipments. It is suitable to use on painted or varnished metal surfaces too. It may have an adverse effect on rubber or plastic. It is advisable to either remove the rubber or plastic parts if possible, or experiment on small portion of such parts before use. The Salient features of Stanrose® Electrosolv are that it provides immediate and efficient cleaning with quick drying property. It has high dissolving and penetration action so easily mixes with solvents and helps cleaning even heavy dirt. It is safe on applied electrical insulation and it is non corrosive nature makes it easier to use even on painted and varnished surfaces without causing any harm to it. It does not contain chlorinated solvents. It has excellent degreasing and emulsification power even for toughest dirt and grime. It can be used as an alternative to conventional electric cleaners. It has eco friendly components making it environment safe product for power generation industry. More Stanrose® Anti Moist Electrosolv Stanrose® Anti Moist Electrosolv is a multi purpose cleaner that easily removes oily soils, displaces water, and leaves behind a lubricating, corrosion protective, non-greasy film, Stanrose® Anti Moist Electrosolv maintains and restores electrical and electronic equipment from the effects of moisture and corrosion. It also protects metals against corrosion. More Stanrose® Fostreat BWT Stanrose® Fostreat BWT is a dry powdered phosphate based treatment used to precipitate calcium hardness as a non adherent sludge. Stanrose® Fostreat BWT is a free-flowing white powder which is readily soluble in water. When Stanrose® Fostreat BWT is added to the boiler water under proper conditions it supplies the necessary phosphate to chemically react with calcium hardness to prevent the formation calcium carbonate, sulphate and/or silicate scales. The reaction between calcium and phosphate produces a finely divided non adherent sludge (calcium phosphate) which remains suspended in the boiler water and removed through blowdown. More Stanrose® Fuel Care Stanrose® Fuel Care is a fuel oil additive specifically designed to act as a water emulsifier and also to disperse and dissolve sludge in all types of fuel grades. This way, fuel blends gain a homogeneous nature while compatibility problems are reduced. More Stanrose® Fuel Demulsion Stanrose® Fuel Demulsification is the breaking of a crude oil emulsion into oil and water phases. More Stanrose® Glass Magic Stanrose® Glass Magic is versatile and safe enough to use on your most delicate glass surfaces, yet is strong enough to quickly cut through the toughest dirt, dust, fingerprint and haze deposits. Stanrose® Glass Magic is biodegradable, ready to use, foaming, nonabrasive, professional grade, non-flammable and non-ozone depleting. More Stanrose® Graffiti Eraser An effective graffiti remover developed for indoor use where occurrences of graffiti must be removed quickly and safely. More Stanrose® Hard Cleaner - MP Stanrose®Hard Cleaner - MP is a versatile concentrated industrial strength surfactant and hard surface cleaner. This product has no free caustic, it relies on the non-ionic, anionic and inorganic detergents to emulsify and rinse clean on all surfaces. The specially selected wetting agents ensure rapid penetration of surface grime layers. More Stanrose® Hyrocarbon Remover Stanrose® Hydrocarbon Remover cleans is a multipurpose neutral cleaner to remove vegetable and animal oils and fats from zinc-silicate coated tanks. "Stanrose® Hydrocarbon Remover" Cleans removes remaining hydrocarbons from any tank surface after carrying light to moderate cargoes or after cleaning with solvent based degreasers. More Stanrose® Degreaser HD Stanrose® Degresol HD is a versatile heavy duty degreaser meant for tough industrial cleaning jobs. It emulsifies greasy, oily soil for easy and complete removal. A special low foam formulation makes this water based cleaner / degreaser ideal for use in automatic floor scrubbing machines. It eliminates costly work stoppages due to foam build-up in the recovery tank. This product is economical and versatile. Its varied dilution ratios enable use in a wide range of applications, from heavy duty degreasing to general purpose cleaning. When used in pressure sprayers, it generates cleaning power without over abundant suds. More Stanrose® Hand Cleaner - HD Stanrose® Hand Cleaner HD removes grease, grime, dirt, oil, wet paint, tar, soot, carbon and much more. Non-toxic and nonflammable, Simple Green® Heavy-Duty Hand Cleaner Gel can be used with salt water, fresh water or without any water at all. More

Stanrose® Seacare OSD-III Dispersants are chemicals that are applied directly to an oil slick. The key components of chemicals dispersants are surface active agents called Surfactants. Stanrose® Seacare OSD-III assists with breaking up the slick into small droplets ranging in size a few micrometers to few millimetres. Chemical dispersants can do this because they contain molecules that are both water compatible and oil compatible. The molecules align themselves around the oil droplets break away from the slick. The Action prevents the coalescence (reforming or joining) of oil droplets. So, the oil can no longer form slick on water surface, and it reduces the adherence of the oil to solid particles ( sand ) and hard surfaces ( sea walls & boat hulls )Chemical dispersants remove the oil from the surface of the water and into the water column. Once in the water column, the oil is diluted to less harmful levels, and eventually is used as a food by bacteria. By removing the oil from the water surface, birds, marine mammals and sensitive coast is protected. Common Name Oil Spill Dispersant, Type-III Product Code STAN-CLC060 Features and Benefits With the break up of the oil into water wetted droplets, the continuity of the fire is disrupted and it also stops any further spread of oil fire. The mixture of Stanrose® Seacare OSD-III and water is non flammable and non hazardous. Stanrose® Seacare OSD is free from Paraffinic Solvents / Polvaromatic and Aromatic Hydrocarbons, Chlorinated Hydrocarbons, Heavy Metals, Benzene, Phenols, Caustic Alkali and free Mineral Acid. Stanrose® Seacare OSD-III is duly tested by National Institute of Oceanography ( NIO, Goa ) Stanrose® Seacare OSD-III is Type III Water base dilutable concentrate which is non corrosive, non hydrocarbon, completely bio-degradable and practically non toxic in dilute form and slight toxic in concentrate form. It mixes well in sea and fresh water where maximum efficiency achieved at 1 : 10 DOR ( Dispersant to Oil Ratio ) in fresh and sea water and in concentrate as well as in dilute form. Stanrose® Seacare OSD-III is more efficient and stable in Diluted form indicating that DILUTION ( in Portable Water ) 1 : 10 ( 1 part of Concentrate & 10 parts of Portable Water ) does not make it less effective & dilutable concentrate increases the effective spraying time, So Stanrose® Seacare OSD-III is highly COST EFFECTIVE. Technical Properties Colour Golden Yellow transparent liquid Odour Free from offensive odor pH 7.2 + 0.5 Solubility in water Soluble in water Specific Gravity at 25°C + 1°C Pour Point - 5°C Conductivity 126.TDS./150 micromhos / cm Viscosity 111.08 cSt. Flash Point Material boils in the cup without flashing at 1000C Spreading coefficient 34 dy/cm2 Toxicity, LC50 Independent results available on request. Efficiency Independent results available onl request. Stability Independent results available on request. Shelf Life 5 years. Recommended Uses Refer technical data sheet Method of Application Refer technical data sheet Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Gum Remover “Stanrose® Gum Remover” is designed to soften and remove residues of chewing gum from floors, carpets, and upholstery. Rapidly lifts chewing gum from carpets and porous surfaces without the need for damaging freeze sprays Use as supplied Suitable for use on most carpets and upholstery within schools, hospitals, leisure complexes and other public areas Heavy duty performance even on old and trodden-in gum Citrus fragrance Common Name Chewing Gum Remover Product Code STAN-CLC108 Features and Benefits Viscous preparation allows precise application and prevents the need for reapplication Removes even the most stubborn gum residue Specialist solvents penetrate around and under the gum softening its bond to surfaces allowing it to be easily peeled. Easy peel prevents damage to the pile of carpets and upholstery. Contains emulsifiers to allow residues to be wiped away with water. No unsightly white marks. Citrus fragrance. Technical Properties APPEARANCE Viscous liquid COLOUR Colourless ODOUR Citus solvent. FLASH POINT (°C) - 4 closed cup SOLUBILITY Emulsifies in water RELATIVE DENSITY 0.72 Recommended Uses Ideal for the removal of chewing gum in all areas where this represents a problem for example in schools, leisure centres, hotels, busses and trains. Method of Application 1. When applying to fabric or carpets test an inconspicuous area first for colour fastness 2. Apply over and around the gum to allow it to penetrate underneath. 3. Allow to penetrate and soften the gum. 4. Peel away the gum with a scraper. 5. Wipe away residues with a damp cloth. Note : when removing gum from non-porous surfaces first score the surface of the gum to allow more rapid penetration. Do not apply to tarmac or asphalt. Storage and Handling Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Keep away from heat, sparks and open flame. Avoid inhalation of vapours. Packing Available 25 Ltr. / 210 Ltr. Download File

Epoxy Flooring Our Services Epoxy Flooring PU Flooring EPU Flooring ESD Flooring Decorative Flooring 3D Flooring Chemical Resistance Car Deck Flooring Repair Mortar We offer wide range of floor coating products and services such as Epoxy Flooring , PU Flooring , PU Concrete Flooring , EPU Flooring , ESD Flooring , Dielectric Flooring , Decorative Flooring , Nuclear Radiation Resistant Flooring , Chemical Resistance Flooring , Car Deck Flooring System , Repair Mortar , etc. We provide services pan India in Mumbai, Tarapur, Boisar, Palghar, Thane, Vasai, Andheri, MIDC, Navi Mumbai, Panvel, Vashi, Pune, Chakan, Hingana, Nagpur, Rau, Indore, Bamunimaidan, Guwahati, Assam, Rakhial, Ahmedabad, Dahej, Manjalpur, Vadodara, Delhi, Ernakulam, Kochi, Kerala, Bengaluru, Bangalore, Miyapur, Hyderabad, Madhya Pradesh, GIDC, Baddi, Himachal Pradesh, Tangra, Kolkata, West Bengal, Ambattur, Chennai, Tamilnadu etc. We provide lowest industrial epoxy flooring cost per square foot in India with best quality.

PU Concrete Flooring Advantages From laying the Starocrete to daily use, regular cleaning and maintenance, there are many advantages for processors and ultimately users of this building material. Here are some advantages of polyurethane concrete in an overview: The short curing time makes it ideal for quick conversions and extensions Chemical-resistant makes it suitable for use in laboratories, practices and workshops PU concrete is impact-resistant, shockproof and resistant to scratches, abrasion and holes. Can be used in many facilities due to temperature resistance from -40°C to 130°C Easy to clean and disinfect Non-slip and can be used according to standards such as DIN 51130 or BGR 181 Recommended Uses Starocrete (PU concrete) is used in many branches of industry, not only in industry, but also in many smaller-scale trades. The positive characteristics, the easy cleaning with achievement of important standards and the longevity are important factors. Here are some examples of the use of PU concrete / polyurethane concrete: Chemical industrial equipment Pharmaceutical industry Research, practices and laboratories Foodstuffs industry e.g. butchery and bakery also wine press and brewery and Cheese and Dairy Surface Preparation Suitable methods are sanding or grinding. Any surfaces that have been contaminated with oils may also require chemical cleaning. Use an industrial vacuum that picks up even small dust particles. The floor must be cleaned of all dusts and residues before starting to prime. Otherwise you will have various particles trapped within the coat and adhesion will be significantly weakened. The less micro-dust on the surface the less primer you will need. For thin cracks it may be necessary to slice them with a cutter before filling in order to improve the anchoring of the grout. Basecoat - Starocrete 1000 Scratchcoat The scratch coat used is usually Starocrete 1000 Scratch coat. Mix Part A and Part B of the Scratchcoat in a clean bucket with Electric Stirrer according to the instructions on the technical data sheet. Starting at the far corner, apply the basecoat by trowel and roller and evenly broadcast the Sand for firm grip with topcoat, into the wet product until all the basecoat is covered, except at the leading edge. DOWNLOAD TDS Topcoat - Starocrete TC 2000 It is important to select a suitable topcoat which will meet all the visual and wearing requirements. Mix the topcoat Starocrete TC 2000 as per the instruction liter. Apply the topcoat by trowel and spike roller. Use the trowel with thickness of 2 mm to get approx. coverage and after that remove the perimeter tape and protect the floor from full traffic for 7 days. DOWNLOAD TDS Topcoat - Starocrete TC 3000 It is important to select a suitable topcoat which will meet all the visual and wearing requirements. Mix the topcoat Starocrete TC 3000 as per the instruction liter. Apply the topcoat by trowel and spike roller. Use the trowel with thickness of 3 mm to get approx. coverage and after that remove the perimeter tape and protect the floor from full traffic for 7 days. DOWNLOAD TDS Topcoat - Starocrete TC 6000 It is important to select a suitable topcoat which will meet all the visual and wearing requirements. Mix the topcoat Starocrete TC 6000 as per the instruction liter. Apply the topcoat by trowel and spike roller. Use the trowel with thickness of 6 mm to get approx. coverage and after that remove the perimeter tape and protect the floor from full traffic for 7 days. DOWNLOAD TDS Other Useful Products Coving & Yellow Lining Material Staroxy 20 SF – Sand Coving Aggregates – Sand, Silica Powder, Talc Powder Staroxy 21 WB – Water base Coving Stancrete 33 PU – PU base Coving Stanrocove 25 – Covefinish Staroxy 22 – Epoxy Coving Paint Starothane 23 – PU Coving Paint Starothane Yellow/White – PU Yellow Lining Paint Staroxy Yellow/White – Epoxy Yellow Lining Paint Read More Pigments Epoxy Pigments PU & EPU Pigments Resinous Concrete Pigments Read More Repair Mortar Starocrackfill – Crack Fill Material Starocrackseal – Crack Seal Material Staroxy Epocrete – Epoxy Mortar Repair Read More

Stanrose® Fuel Demulsion Stanrose® Fuel Demulsification is the breaking of a crude oil emulsion into oil and water phases. Common Name Fuel Emulsion Breaker Product Code STAN-FOT191 Features and Benefits From a process point of view, the oil producer is interested in three aspects of fuel demulsification : Rate or the speed at which this separation takes place Amount of water left in the crude oil after separation Quality of separated water for disposal Technical Properties Stanrose® Fuel Demulsification is an aid to the physical removal of water from all grades of fuel. Recommended Uses Stanrose® Fuel Demulsification improves centrifugal separation of fines, it helps prevent sludge formation and stabilises fuel viscosity. The fuel filters and lines will be cleaner with less inclination towards blockage. The main purpose of Stanrose® Fuel Demulsification is however to rapidly split water in oil emulsions. Method of Application Breaks water-in-oil emulsions by lowering the surface tension between the two phases. It is insoluble in water and remains effective even after the water has been removed. Powerful dispersants combat existing sludge formations while homogenizing the fuel to prevent new sludge from being formed. Stanrose® Fuel Demulsification lowers the surface tension between the oil and water phases in an emulsion. It is completely insoluble in water and remains in the fuel oil phase. It also disperses sludges and any heavy particles into thefuel oil. Dosing Instructions: Stanrose® Fuel Demulsification is dosed to the bunker tank prior or during bunkering. Dosing is based on water content using test results. If none are available an initial dose of 1:4000 should be used. Water % Vol 0.5 – 1.0 1.0 – 2.00 >2.0 Dose Rate 1: 4000 1 : 2000 1 : 1000 Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

OUR MISSION Our company mission is to understand customer’s need & provide true, commercial-grade floor coating systems to have the same durable, professional quality floor coating at a fraction of the cost. Our goal is to provide you with the proper solutions with unerring quality & cost competency by adopting complete honesty & dignity in all our dealings. OUR TEAM We possess a sincere and dedicated team of professionals who play a vital role in the growth of our organization. Our team is full of trained members who are capable of understanding the different requirements of clients in an effective manner. We have procured agents, applicators, quality controllers, warehouse & packaging personnel and sales & marketing personnel. Our professionals work in close coordination with each other to attain 100% client satisfaction. With their vast domain knowledge and experience, we are able to offer appropriate products to our customers. Besides, our professionals also undertake and accomplish waterproofing, wall coating and flooring works with utmost perfection. QUALITY STANDARDS Being a trusted organization, we pay utmost attention on quality factor. All our sourced range is rigidly tested by our quality controllers in order to ensure flawless products to our coveted customers. The company is accredited with EN ISO 9001: 2015 quality management system certification and EN ISO 14001: 2015 environment management system certification for its ability to design and develop solutions /products coupled with a good manufacturing practices / service. Our construction chemical products for Epoxy Flooring, PU Paints and Coatings, Epoxy Primers, Solvented and Solventfree Coatings, Nuclear Radiation Resistant Coating, Heat Reflector and Waterproofing Coatings follow approvals by recognized bodies such as Central Food Technological Research Institute - CFTRI, Counsil of Scientific and Industrial Research - CSIR, Central Power Research Institute - CPRI, National Test House - NTH, Electrical Research and Development Association - ERDA, Veermata Jijabai Technical Institute - VJTI, Board of Radiation and Isotope Technology - BRIT, Nuclear Power Corporation of India - NPCIL, ISOMED as per industry standards

Stanrose® Hard Cleaner - MP Stanrose®Hard Cleaner - MP is a versatile concentrated industrial strength surfactant and hard surface cleaner. This product has no free caustic, it relies on the non-ionic, anionic and inorganic detergents to emulsify and rinse clean on all surfaces. The specially selected wetting agents ensure rapid penetration of surface grime layers. Common Name Hard Surface Cleaner – Multi Purpose Product Code STAN-CLC113 Features and Benefits No fumes or added perfumes Can be used as “spray‐on, wipe‐off” Safe on aluminium Biodegradable Safe in Septic systems Technical Properties Refer technical data sheet Recommended Uses This product has no free caustic, it relies on the non-ionic, anionic and inorganic detergents to emulsify and rinse clean on all surfaces. Method of Application General Manual Cleaning: Dilute 40: 1 with potable water (25ml per Litre) If the surface is covered with dirt's, fat, grease or oil specially in tiled or floor areas, a dilution of 20:1 (50ml per Litre) is recommended. Hard Job Cleaner may be used in urinal troughs, toilet bowls, along shower benches and hand basins. Dilute 10:1 in a squirt bottle, scrub then flush with clean water. Hard Job Cleaner will also clean surfaces contaminated with water based paints or inks. To remove lipstick tar, gum or hard to remove stains, apply straight form the bottle. Hard Job Cleaner may also be used as a surface cleaner for trucks, cars, annexes and trailers. Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Bank Details To Deposit Amount to Akshardhara's account. ​ Account Name - Stanrose Envirotech India Pvt Ltd ​ Bank Name - HDFC BANK LTD Branch - Boisar ​ Bank Address - B Wing, 1st Floor, Shivkala Arcade, Boisar Tarapur Road, Boisar- 401501 IFSC Code - HDFC0000160 Account No - 50200040596199 Account Type - Current A/c Once you deposit bill amount send sms/whatsapp to +917620600130 in following format [Your name, Deposited Amount, Date, Time; | For Example, Sameer, Rs. 200/-, 01/10/2017, 04:20 (approx)] or mail at admin@stanrose.co.in in same format or call on 7620600130 | 8655730738 (10 am to 7 pm)

Interior Paints Highlights Interior paint is more to do with aesthetics and decoration purposes and at the same time, they need to add properties of easy maintenance, wash ability and dampness prevention. It’s designed to withstand abrasion. Interior paint is also designed to be more delicate than exterior paint because they occupy the same space as you do. Interior paint is so made that they can be scrubbed and can resist staining. Interior paint is formulated to be more resistant to physical damage. The resins used for interior paint can be firmer because the paint does not have to deal with weather and temperature differences like exterior paint. Interior paint is not required to be fade resistant as they are not subject to extreme temperature conditions and hence do not fade easily. Interior paints need to be stained resistant for hiding brush and roller marks. Interior paint should get cured even without direct exposure to sunlight. Interior paint does not require additives like pesticides and fungicides. It is made washable so as to clean spots and marks that they accidentally get especially by small kids and pets at home. Interior paint should have a low or zero VOC (Volatile organic compounds). This is important in preserving the air quality in your home. Low or zero VOC help to reduce your health risks. Our products have been tested and approved by trusted authorities such as CFTRI, CSIR, VJTI. STAROXY NPE CRC 90 Description: - Staroxy NPE CRC 90 is a 100% solids epoxy Novolac coating ideal for harsh chemical and solvent resistant applications. It is used in secondary containment, solvent storage, pump pads, trenches, and other high exposure areas. Novolac Epoxy - Highly Chemical Resistant Epoxy - is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities. It is commonly used as a seal coat for Epoxy Mortar Systems where chemical resistant performance is required. Advantages: - Exhibits excellent resistance to strong acids, alkalis, and most industrial chemicals and solvents Can be applied in cool damp conditions Can be re-coated in 4 to 6 hours Can be applied in occupied facilities Forms a virtual moisture barrier 100% solids - 0.0 lbs VOC - meets even the most strict low VOC requirements Technical Properties: - Color: RAL shades Solids Content: 100% Gloss 60 F: 100 Mix Ratio: 2.1-A to 0.9-B by weight Pot Life: 20 minutes @ 75 F VOC: 0% Foot Traffic: 10-12 hours Recoat - Minimum: 4 - 12 hours (Depending on Temperature) Recoat - Maximum: 24-36 hours (Depending on Temperature) Service: 5 days Mechanical Properties: - Tensile Strength ASTM-D-638: 10,400 p.s.i Adhesion to concrete ACI Committee 403: 300 p.s.i - 100% concrete failure Hardness ASTM-D-2240: 86 Shore D Abrasion Resistance ASTM-C-501: CS-17 Wheel 30 mg lost Service Temperature MIL- D-3134F: Up to 180-325 degrees F. Dry Heat Elongation: 2.5% STAROXY CRC 90 Description: - Staroxy CRC 90 is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkaline for both interior and exterior applications. Advantages: - Excellent chemical resistance Strong yet resilient Built in flexibility Sprayable Technical Properties: - Mix Ratio: 2.5-A : 1.5-B By Weight Viscosity (mixed): 1800 CPS Pot Life (200 gr.): 40 minutes Tack Free to Touch: 6-8 Hours Initial Cure: 24 Hours Final Cure: 7 Days Packaging (unit size): 3 ltr. 15 ltr. Standard Colors: Black, White, & standard colors Mechanical Properties: - Tensile Strength (ASTM D-638): 5500 p.s.i. min. Elongation: 5%+ STAROXY CRC 80 Description: - Staroxy CRC 90 is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkaline for both interior and exterior applications. Advantages: - Excellent chemical resistance Strong yet resilient Built in flexibility Sprayable Technical Properties: - Mix Ratio 2.5-A : 1.5-B By Weight Viscosity (mixed): 2000 to 2500 CPS Pot Life (200 gr.): 40 minutes Tack Free to Touch: 4 to 8 Hours Initial Cure: 24 Hours Final Cure: 7 Days Packaging (unit size): 3 ltr. 15 ltr. Standard Colors: 15 Colors + Special Mechanical Properties: - Tensile Strength (ASTM D-638): 5500 p.s.i. min. Elongation: 5%+