COntact No. 07020814816 / 08087778631 Email: / Address: G 17/8, Tarapur MIDC, Boisar West, 401506
STANROSE COVING MATERIAL
COVING MATERIAL
STAROXY 20 SF - Epoxy Sand Coving Material
Description
Staroxy 20 SF Coving is a 100% solids epoxy cove system, used to protect vertical surfaces subject to chemical attack. Applied at 1/8" nominal film thickness.
Advantages: -
-
Cures quickly to form an exceptionally tough, impact and abrasion resistant system. Excellent adhesion to concrete, steel, and wood. Minimum down time. Sanitary, non‐shrinking polymer.
-
Easy to clean.
-
Not affected by water, oil, brine, most acids, and alkaline. For specific recommendations, please refer to Stanrose's Chemical Resistance Guide, or contact Technical Service.
-
Used as part of a polymer system for resurfacing food production plants, aisle ways, chemical spill containment area's, industrial production facilities, and pulp and paper mills.
Technical Properties:
-
Components: Resin & Hardner
-
Ratio: 2:1
-
Coverage: 10.5 m in 3 kg kit for 3 x 3 ich coving (with aggregates)
-
Curing time for Light Traffic: 24 Hrs.
-
Curing time for heavy traffic: 96 Hrs.
Mechanical Properties:
-
Compressive Strength (ASTM D695): 11,500 psi (resin)
-
Modulus of Elasticity (ASTM D695): 1.062 X 10⁶
-
Tensile Strength (ASTM D638): 1,700 psi (resin)
-
Flexural Strength (ASTM D790): 3500 psi (resin)
-
Bond Strength, (ASTM C‐321): Greater than 350 psi (100% substrate failure)
For Application Instructions and Storage Condition requirements please download TDS.
Click Here to download TDS
STAROXY 21 WB - Waterbased Epoxy Sand Coving Material
Description
Staroxy 21 WB is a three-component water dispersed epoxy resin coving system supplied in pre-weighed packs ready for on-site mixing and use.
To provide a dust-proof easily cleaned surface which is resistant to most oils and liquids. It is suitable for use on:
- Walls and floors in warehouses.
- Garages.
- Light industrial and food processing areas.
- Kitchens and other areas of pedestrian and light vehicular traffic.
Advantages: -
- Antibacterial - resists bacterial growth.
- Durable - good resistance to abrasion.
- Economical - easy to apply, minimizes cleaning costs.
- Water based - safe in use, low odour.
- Attractive - available in a range of colours.
- Good resistance to a wide range of chemicals.
Technical Properties: -
-
Component: Ratio:Hardner
-
Ratio: 1:3
-
Coverage: 14 m in 4 kg kit for 3 x 3 ich coving (with aggregates)
-
Pot Life: 4 Hrs.
-
Time between coats: 6-24 Hrs.
-
Initial Hardness: 24 Hrs.
-
Full Cure: 7 Days
For Application Instructions and Storage Condition requirements please download TDS.
Click Here to download TDS
STANCRETE 33 PU - PU Cementitious Coving Material
Description
Stancrete 33 PU is a three-part urethane polymer concrete Cove Base product. It is designed to withstand aggressive chemical attack, thermal shock resistance, and can be used as a patching material.
It is an integral part of the Starocrete PU flooring family of products. The vertical portion can be installed to any height at 1/16" to 1/4" thickness.
Features:
-
Water-Based Low Emitting Materials
-
Contains 20% Plant-Based
-
Meets USDA, FDA and CFIA Standards
-
Superior Impact Resistance
-
Excellent Chemical Resistance
-
Meets California VOC and SCAQMD Requirements
-
Wide Temperature Service Range from -50ºF to 200ºF
-
Cold Temperature Application
-
High Tolerance to Moisture Vapor
-
Green Concrete Applicable, 7 days
-
Resistance to Growth of Bacteria and Fungi
Cove Base Advantages:
-
Prevents water from going under the walls
-
Contains chemicals within the coved area
-
Makes it easy to clean and disinfect the edges of the floor
-
Does not allow bacteria or insects to hide under the Wall
-
Gives the floor an attractive, professional, and seamless look
-
Ideal for food and pharmaceutical applications
Recommended Uses: -
Chemical Processing, Food Processing Areas, Restaurants, Pharmaceutical, Bakeries, Cage Wash Areas, Bottling Areas, Sanitize / Wash Areas, Plant Vehicle Aisles, Warehouses, Mechanical Room
Technical Properties:
-
Components: Resin & Hardner
-
Ratio: 1:1
-
Coverage: 7 m in 2 kg kit for 3 x 3 ich coving (with aggregates)
-
Curing time: 6-8 Hrs.
-
Pot Life: 15-20 Minutes.
Mechanical Properties: -
-
Hardness (ASTM D 2240): 80D
-
Compressive Strength (ASTM D 579): 6000 psi
For Application Instructions and Storage Condition requirements please download TDS.
Click Here to download TDS
STANROCOVE 25 - Cleaning of Coving
Description
Stanrocove 25 used to clean and increase gloss of coving. It is almost colorless, Odourless or slight aromatic, ester odour oily liquid, free of foreign materials in soluble in water but miscible in organic solvents.
Chemical Properties: -
Color HU (ASTM D1045-86): 20 max
Specific Gravity (ASTM D1045-86): 1.030-1.041
Boiling Point: 346°C
Viscosity: 23 cp
STAROXY 22 - Epoxy Coving Paint
Description
Staroxy 22 is two-component epoxy coating that is specially formulated to provide an attractive and durable finish.
This is a two-component amine cured solvent free epoxy coating. It is a self-smoothing, easy to apply product, leaving a seamless surface. It has excellent chemical, abrasion and impact resistance. If enhanced slip resistance is required Staroxy Deck Guard 500 can be used in the system. Can be applied directly in two coats or on approved primers depending on the conditions of the concrete substrate.
Features: -
- A durable finish coat for epoxy-based coating systems.
- Tough, hard wearing finish with overall durability properties.
- High resistance to impact and abrasion.
- Excellent adhesion to aged epoxy coatings.
- Resistance to spillage or splashes of mild chemicals.
Typical Use: -
Designed for a wide range of floors with various levels of mechanical and chemical exposure. Recommended for warehouses, garages, dairies, factories, laboratories, aircraft hangars, food, beverage and plant rooms.
Technical Properties:
-
Components: Resin & Hardner
-
Ratio: 2:1
-
Colour: As per RAL shade
-
Coverage: 105 m in 3 kg kit for 3x3 inch coving (with aggregates)
-
Surface (Touch) Dry: 7 Hrs.
-
Walk-on-dry: 14 Hrs.
-
Pot Life: 20 min.
-
Dried for service: 3 Days
-
Thinner / Cleaning Solvent: Stanrose Epoxy Paint Thinner
Mechanical Properties:
-
Solids by Volume (ISO 3233): 96%
-
Gloss Level (ISO 2813): Gloss 70-85
-
Flash Point (ISO 3679): 100°C
For Application Instructions and Storage Condition requirements please download TDS.
Click Here to download TDS
STAROTHANE 23 - PU Coving Paint
Description
Starothane 23 is two-component Polyurethane coating that is specially formulated to provide an attractive and durable finish.
This is a two-component aromatic isocyanate cured polyurethane coating. It is a high performance, solvent free product. It is a self levelling product leaving a seamless surface. It is flexible, abrasion, impact, chemical and slip resistant. It is specially designed to be used as a waterproof membrane. If enhanced slip resistance is required Staroxy Deck Guard (Anti-Skid) can be used in the system. To be used as mid coat as part of a complete system in atmospheric environments. Suitable on approved primers on concrete substrates.
Technical Properties:
-
Components: Resin & Hardner
-
Ratio: 3:1
-
Colour: As per RAL shade
-
Coverage: 140 m in 3 kg kit for 3x3 inch coving (with aggregates)
-
Surface (Touch) Dry: 7 Hrs.
-
Walk-on-dry: 14 Hrs.
-
Pot Life: 15 min.
-
Dried for service: 3 Days
-
Thinner / Cleaning Solvent: Stanrose PU Paint Thinner
Mechanical Properties:
-
Solids by Volume (ISO 3233): 96%
-
Gloss Level (ISO 2813): Gloss 70-85
-
Flash Point (ISO 3679): 100°C
For Application Instructions and Storage Condition requirements please download TDS.
Click Here to download TDS
AGGREGATES
FINE TALC POWDER
Description
Talc is a soft, lamellar inert mineral, which occurs typically as magnesium silicate. The Talc grades exhibit good purity and chemical stability.
As the strengthening modified filler, it increases the stability of the product's shape, increase tensile strength, shear strength, flexural strength, compressive strength, reduce distortion, stretching, thermal expansion coefficient, high brightness, dispersion of uniform size.
Technical Properties: -
-
Particle Size (μm) 22
-
SiO2 ≥ % 50~60
-
MgO ≥ % 28
-
Whiteness (%) 92
-
Absorption Oil Volume% 20 ~50
-
Moisture (%) ≤0.5
-
Loss of Ignition(1000ºC) % 6
-
Water Solute % ≤0.1
-
Acid Solute % ≤1.5
-
Asbestos 0
-
CaCO3 % 0.5
-
Al2O3% 0.05
-
Fe2O3 % 0.01
-
Ph Value 7~9
-
Bulk Density 0.2
SQ FINE POWDER
Mainly Used for: -
-
Filler -
Coving
SQ SAND 100
Mainly Used for: -
-
Sand Broadcasting Material (Anti Slip Grains for Parking Area) -
Coving
SQ SAND 50150
Mainly Used for: -
-
Sand Broadcasting Material (Anti Slip Grains for Parking Area) -
Coving
SQ SAND 1632
Mainly Used for: -
-
Sand Broadcasting Material (Anti Slip Grains for Ramp) -
Coving
SQ SAND 3080
Mainly Used for: -
-
Sand Broadcasting Material (Anti Slip Grains for Drive Way) -
Coving