Search Results

Epoxy Flooring Benefits Hygienic - It provides a jointless epoxy flooring making it dust free & easy to clean Chemical resistance - It has excellent chemical resistance to most chemicals Wear resistance - It provides a tough floor topping to withstand foot & light vehicular traffic Good abrasion resistance & good UV stability Where it is used? Staroxy (Epoxy) HG is recommended for use where extremely hygienic, abrasion, chemical resistant and dust free environment is required. It is ideally suited for flooring in following industries. Pharmaceutical Industries Electronic Assembly Areas Clean Rooms Food Processing Industries Scope Of Work Surface preparing by removing of dust, oil, grease, unwanted cements etc. through heavy duty grinding machine for exposing the micro pores on concrete. Filling of control joints, holes and uneven surface through epoxy mortar Applying of Staroxy Primer let it cure for 8 hrs. Application of Staroxy UL (Self Levelling Screed). Applying of Staroxy SL as per recommended thickness and let it cure for 36 hrs. (for optimum result) Surface Preparation Suitable methods are sanding or grinding. Any surfaces that have been contaminated with oils may also require chemical cleaning. Use an industrial vacuum that picks up even small dust particles. The floor must be cleaned of all dusts and residues before starting to prime. Otherwise you will have various particles trapped within the coat and adhesion will be significantly weakened. The less micro-dust on the surface the less primer you will need. For thin cracks it may be necessary to slice them with a cutter before filling in order to improve the anchoring of the grout. Primer - Staroxy 103 MOT Mix Part A and Part B of Staroxy 103 MOT with Electric Stirrer. Once parts A & B have been thoroughly mixed, the product may be thinned to aid application. Apply the primer coat by brush and then roll the centre with a short nap roller. Allow a drying time of at least 4 hours before applying basecoat. If you intend to install epoxy corner coving, this should be done before commencing the next step. Click Here For List of Staroxy (EPOXY) Primers Basecoat - Staroxy UL 1000 The base coat used is usually Staroxy UL. Mix Part A and Part B of the Staroxy UL in a clean bucket with Electric Stirrer according to the instructions on the technical data sheet. Starting at the far corner, apply the basecoat by trowel and roller and evenly broadcast the Sand if necessary, into the wet product until all the basecoat is covered, except at the leading edge. Click Here For List of Staroxy (EPOXY) Underlay/Basecoat Topcoat - Staroxy SL 1000 It is important to select a suitable topcoat which will meet all the visual and wearing requirements. Mix the topcoat usually Staroxy SL 1000 as per the instruction letter. Remove the perimeter tape and protect the floor from full traffic for 7 days. Click Here For List of Staroxy (EPOXY) Topcoats Roller Topcoat - Staroxy SL 300/500 Once ready to apply topcoat (waiting overnight for the basecoat to efficiently cure), mix Part A and Part B together. Refer to 'Mixing Section' of this product data sheet. Continue mixing throughout application. Be sure to roll one even coat of Staroxy SL 300 topcoat to entire surface to be coated. Click Here For List of Staroxy (EPOXY) Roll-on-Topcoats Other Useful Products Coving & Yellow Lining Material Staroxy 20 SF – Sand Coving Aggregates – Sand, Silica Powder, Talc Powder Staroxy 21 WB – Water base Coving Stancrete 33 PU – PU base Coving Stanrocove 25 – Covefinish Staroxy 22 – Epoxy Coving Paint Starothane 23 – PU Coving Paint Starothane Yellow/White – PU Yellow Lining Paint Staroxy Yellow/White – Epoxy Yellow Lining Paint Read More Pigments Epoxy Pigments PU & EPU Pigments Resinous Concrete Pigments Read More Repair Mortar Starocrackfill – Crack Fill Material Starocrackseal – Crack Seal Material Staroxy Epocrete – Epoxy Mortar Repair Read More

Privacy Policy Thank you for visiting Stanrose. This privacy policy tells you how we use personal information submitted or collected at this site with your consent. Please read this privacy policy before using the site or submitting any personal information. By using the site or the various features available and present herein, you are accepting the practices and the standard operating procedure as described in this privacy policy. These practices may be changed time to time as part of continuous change and applicability of new legal and statutory provisions which are binding upon us as a law abiding corporate citizen but any changes which could be undertaken by the Company shall be published and changes will only applicable to activities and information on a prospective basis, not retroactively. You are encouraged to review the privacy policy whenever you visit the site to make sure that you understand how any personal information you provide will be used. ​ Collection of information This notice applies to all information collected or submitted on our website. Stanrose collects or requests you to submit personal information, such as your e-mail address, name, home or work address or telephone number. Information collected by Stanrose.org by us is used only for the purpose of billing and shipping your online purchased purchases. We do not collect any information about your computer hardware, software or payment information. Neither we sell/disclose/share/distribute sensitive information to any 3rd party for any purpose except to extent of delivery of ordered products. ​ Use of the information We use the information that we collect from you to provide our services to you. In addition to this we may use the information for one or more of the following purposes: To provide information to you that you request from us relating to our products or services. To provide information to you relating to other products that may be of interest to you. Such additional information will only be provided where you have consented to receive such information and the same is existing with us at the time of utilization of the consent so provided by you. To inform you of any changes to our website, services or goods offered by various Vendors. If you have previously purchased goods or services from us we may provide to you details of similar goods or services, or other goods or services, that you may be interested in. We use return email addresses to answer the email and we don’t use the same for any other purpose. Legal distribution of information We may share information with Governmental Agencies or other companies assisting us in fraud prevention or investigation. We may do so when: (1) permitted or required by law; or, (2) trying to protect against or prevent actual or potential fraud or unauthorized transactions; or, (3) investigating fraud which has already taken place. ​ Information automatically collected when you visit website When you visit our websites, we automatically record information that your browser sends whenever you visit a website. For example, we may receive and collect: the name of the domain and host from which you access the Internet; the Internet Protocol (IP) address of the computer you are using; the date and time you access our websites; and the Internet address of the website from which you linked directly to our sites. We use this information to monitor the usage of our websites and as necessary for our business. This information does not include personal information. ​ Information collection using cookies Cookies Definition : Cookies are small text files that are placed on your computer or mobile device by websites that you visit. They cannot harm your computer and do not contain any information that enable us to identify you personally, they just enable our websites to recognize your computer and to identify certain other non-personal information such as which browser you are using. This information can be used to make the website work, to identify which parts of the site can work better or to analyse how often people visit the site and what they look at. We will not associate this data with any personally identifying information that you may choose to provide to us in other ways. By your using this website, we imply that you have read this policy and agree to us sending you cookies. Links to other website and products & social media Stanrose may provide you with the ability to register, log into, “like” or otherwise interact with third party social media services, including, but not limited to, Facebook, Instagram, Twitter, Pinterest, YouTube, and other social media services. These features may enable integration and/or access to your social media accounts. We do not control these social media services or your profiles on these services, and we do not establish privacy settings or rules for how your personal information on these services will be used. If you choose to log on to or submit information through any of these social media services, your personal information will be subject to the applicable social media service’s terms and conditions and your current privacy settings on such social media service. By accessing any social media service, you will be assuming the risk that the personal information you provide on that service may be viewed and/or used by third parties for any purpose. You agree that Stanrose not responsible for any acts or omissions by these social media service providers. In addition, by choosing to log in to our Sites using your credentials from a social media service, you are asking that service to send us certain information from your account with the service, and you authorize us to collect, store and use such information in accordance with this Privacy Policy. ​ Query / Questions If You Have any Query / Questions then Mail us on Following mail ID in any of English / Hindi Language. admin@stanrose.co.in

EPU Flooring Highlights Advantages Intended Use Heavy Duty Epoxy Polyurethane Based Screed Tolerates Oil Contamination Flexible than epoxy High strength Recommended on oil contaminated surface Self-leveling property High flexural & compressive strengths Engineering Garages Manufacturing units Warehouses requiring tolerance to oil contamination Topcoat - Staroxen SL 1000 It is important to select a suitable topcoat which will meet all the visual and wearing requirements. Mix the topcoat usually Staroxen SL 1000 as per the instruction liter. Remove the perimeter tape and protect the floor from full traffic for 7 days. Click Here For List of Staroxen (EPU) Topcoats Roller Topcoat - Staroxen SL 300 Once ready to apply topcoat (waiting overnight for the basecoat to efficiently cure), mix Part A and Part B together. Refer to 'Mixing Section' of this product data sheet. Continue mixing throughout application. Be sure to roll one even coat of Staroxy SL 300 topcoat to entire surface to be coated. Click Here For List of Staroxen (EPU) Roller Topcoats Other Useful Products Coving & Yellow Lining Material Staroxy 20 SF – Sand Coving Aggregates – Sand, Silica Powder, Talc Powder Staroxy 21 WB – Water base Coving Stancrete 33 PU – PU base Coving Stanrocove 25 – Covefinish Staroxy 22 – Epoxy Coving Paint Starothane 23 – PU Coving Paint Starothane Yellow/White – PU Yellow Lining Paint Staroxy Yellow/White – Epoxy Yellow Lining Paint Read More Pigments Epoxy Pigments PU & EPU Pigments Resinous Concrete Pigments Read More Repair Mortar Starocrackfill – Crack Fill Material Starocrackseal – Crack Seal Material Staroxy Epocrete – Epoxy Mortar Repair Read More

Stanrose® Biostan Oil Cleaner "Stanrose® Biostan Oil Cleaner" is a very strong cleaner, which can be used to soften up / remove baked on drying oils and used after animal and vegetable oils, fish oils, tall oils, tug oils etc .It is low toxic product with an exceptional solvency power on soil & oily matter. It is free from hydrocarbon solvents, Biodegradable minimizes the extreme hazards to personnel in handling materials. Common Name CTC Volc Cleaner Product Code STAN-CLC069 Features and Benefits Removes grease, oil, carbon deposits, soil and grime. Keeps loosened deposits in suspension preventing re-deposition. Low toxic. , Non-flammable. Free from hydrocarbon solvents. Effective and economical in use , Water-based cleaner. Technical Properties Appearance Slightly Yellow Viscous Ordour Characterisric Density 1.00 at 20°C Flash Point None pH 7 at 20°C pH Neat None on Cement, Ceramic Tiles, Vinyl or Metal Surfaces Recommended Uses It is a very strong cleaner, which can be used to soften up / remove baked on drying oils and used after animal and vegetable oils, fish oils, tall oils, tug oils etc Method of Application First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using "Stanrose® Biostan Oil Cleaner" is by direct injection followed by re-circulation washing, using tank cleaning machines. Spraying Method : Using "Stanrose® Biostan Oil Cleaner" as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry. **Make sure to take all safety precautions are followed when handling / spraying "Stanrose® Biostan Oil Cleaner"** Injection Method : Not applicable. Re- Circulation Method : Fill tank with fresh water and heat up to warm 50o C . If a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and "Stanrose® Biostan Oil Cleaner" to make a 2.5% solution. A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank. Under normal circumstances, between 2.5% and 4.5% will be sufficient strength. If there is no drop line, then lower butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material. **Use a strainer at the pump stack when circulating any solution.** Tank Lining– Stainless / Epoxy / Phenolic. Dosage : Necessary concentration in water only 0,2 to 0,4 % Storage and Handling Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Dual Purpose Stanrose® Dual Purpose is a specially formulated blend of organic dispersing agents, water displacing surfactants and combustion catalysts. This product is designed to meet two objectives: 1. Improve the precombustion characteristics of light and heavy fuels. 2. Introduce combustion catalysts into the combustion zone to improve combustion efficiency and minimize fireside corrosion and deposit problems. Common Name Dual Purpose Plus /Concentrated Combustion Improver Product Code STAN-FOT190 Features and Benefits Stanrose® Dual Purpose reduces fuel consumption and pollutant emissions. Stanrose® Dual Purpose improves the quality of fuel. Stanrose® Dual Purpose removes the existing deposits and keeps the injector nozzles clean. Stanrose® Dual Purpose protects the system from corrosion. Stanrose® Dual Purpose minimizes the Sludge formation. Stanrose® Dual Purpose reduces maintenance costs. Technical Properties Appearance : Dark Brown Liquid Specific Gravity 20°C : 0.87 Flash Point PMCC : Above 66°C / 150°F Viscosity : 60 sec at 400 by Redwood viscometer no. 1 Recommended Uses FUEL CONDITIONER Stanrose® Dual Purpose will reduce sludge and gum formation in tanks, feed lines, oil pre-heaters, strainers and burners. Sludging potential of oil is greatly increased by the presence of water. Stanrose® Dual Purpose contains an emulsion breaker which separates the water from the oil. This separation will also reduce some serious fireside slags. The sodium ion in saltwater if carried into the combustion chamber will reduce the melting point of vanadium forming a molten slag. COMBUSTION CATALYST Stanrose® Dual Purpose contains combustion catalysts which function by providing the fastest possible reaction time of the air fuel mixture assuring that complete combustion is achieved in the shortest time possible. This results in the minimization of soot, fly ash, intermediate combustion products and unburned particulate matter. Stanrose® Dual Purpose will prevent Low Temperature Corrosion by allowing minimum excess air conditions to be approached as a result of improved combustion reactions and by eliminating the catalytic effect that produces sulphur trioxide. Stanrose® Dual Purpose further protects against low temperature corrosion by preventing acidic deposits of particulate matter. By way of review, sulphur dioxide and sulphur trioxide are normal combustion products when firing fuels containing sulphur. The concentration of sulphur trioxide in the flue gas in relation to sulphur dioxide is dependant on the excess air employed and the presence of vanadium and iron oxide. It has been estimated that 75% of the sulphur trioxide is formed from sulphur dioxide in the combustion area. The reaction occurs as a result of sulphur dioxide combining with nascent oxygen and is aided by the catalytic effect of vanadium and iron oxide. Sulphur trioxide concentration in the flue gas determines the acid dew point. Acid dew point is defined as that temperature at which the water vapour present in the flue gas as a result of combustion can combine with sulphur trioxide to form sulphuric acid. Low temperature corrosion results when the flue gas cools below the acid dew point. This condition is found in pre-heaters, economizers, cold end of boilers and in the stack. This problem is particularly severe when maximum heat recovery from the flue gas is desired. AIR POLLUTION Stanrose® Dual Purpose will reduce air pollution by minimizing the amount of undesirable constituents in stack gases. Burning of fuel containing sulphur will result in the formation of sulphur dioxide and sulphur trioxide trioxide. The use of Stanrose® Dual Purpose and good combustion controls will retain most of the sulphur in the dioxide from and minimize the formation of the highly undesirable sulphur. Unburned residues and fly ash are also minimized in the stack gas because of the improved combustion reaction. This results in the maintaining of a clean stack and the reduction of undesirable particulate matter. The complete burning of the fuel will also eliminate the unwanted products of partial combustion such as aldehydes and ketones. Method of Application Average dosage rates are one litre per 2 to 4 tons of fuel, Apply directly to tanks when bunkering, normally down the souding tube. If sludge breaking is not a problem in the double bottoms apply directly to day tank or for more accurate control we recommend that Stanrose® Dual Purpose be metered directly into the fuel supply line. The best way is to start on a Diesel Engine, which has just completed overhaul. On such an engine, one can see the difference by checking following and comparing with the period when "Stanrose® Dual Purpose" was not being used. 1. Fuel Oil Filters condition / time between cleaning. 2. Fuel Injectors condition / time between overhauls. 3. Exhaust from the Engine - colour/ Extent. 4. Piston Rings Breakage if any caused due to unburned fuel and heavy carbon deposits. 5. Time between overhaul of Inlet / Exhaust Values. 6. Time between Piston overhaul. 7. Burning of Piston Heads. 8. Corrosion, if any, on components such as liner. 9. Presence of carbon in crank case oil caused by blow past due to sticky /broken Piston Rings. Since, complete combustion means full utilization of the calorific value of the fuel, there is a definite saving in specific Fuel consumption, when above conditions are maintained. Storage and Handling Avoid contact with skin and eyes. In case of contact flush with plenty of water. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Polyurea Coating Highlights Polyurea is an elastomer substance derived from step-growth polymerization, which involves combining a synthetic resin and isocyanate reactive materials. Thus, the reaction of an isocyanate part with a resin blend component part through the step growth process of polymerization produces polyurea. Highlights High Flexibility High Elongation Waterproof Fast Cure Sound Dampening High Impact Resistance High COF Used for containment Reduces sound pollution No cracking or warping High traction Protects against rust and rot High cohesive properties Compared to epoxy coating, polyurea is greatly superior in moisture resistance, UV resistance (for aliphatic coatings), abrasion resistance, chemical resistance, temperature resistance and durability. It also has a quicker cure time. Compared to polyurethane, polyurea has superior durability, chemical resistance and moisture resistance. Approved by recognized authorities such as BARC, NPCIL. Surface Preparation New surfaces must be allowed to cure completely. It is recommended to allow 28 days as the curing time for new surfaces. Surface should be free from any loose paint, dust or grease. Growths of fungus, algae or moss should be removed by wire brushing and water. In case of areas having excessive dampness using Stanrose Damp Block to limit further dampness. When the underlying surface exhibits chalkiness, in spite of thorough surface cleaning, use Stanrocrackseal. In case of dents and holes use Stanrose Wall Putty or white cement and fine sand in the ratio 1:3. Staropolyurea Mix the constituents as per the supplied pack. The ratio of Resin to Hardner is 1:0.32 by weight. Stir the mixture properly by Electric Mixer. Apply the mixture with the help of brush or spray. DOWNLOAD TDS HERE

Stanrose® SPOL "Stanrose® SPOL" is a pH-neutral, liquid concentrated detergent with good cleaning qualities. It is multi- purpose heavy duty cleaning soap solution used as a common dirt remover in residential, commercial and industrial cleaning processes. It contains effective but mild and environmentally safe wetting agents and surfactants that allow rapid penetration to remove fats and oils. "Stanrose® SPOL" is especially suitable for hydrocarbon freeing of tanks, and is safe on all tank coatings including zinc silicate. Common Name Tank Cleaning Surfactants Product Code STAN-CLC056 Features and Benefits Non-caustic, pH neutral Solvent free Non-flammable Does not contain nonylphenol ethoxylates or other estrogenic compounds Non-corrosive to metals Suitable for all tank-coatings Can be used for gas and hydrocarbon-freeing of tanks Can be used for deodorizing Complies with all environmental regulations and the EU Detergent Regulation Technical Properties Form Liquid Appearance Light Yellow Density 1, 1 pH, in Conc 8-9 pH, in 1% Sol 7-8 Recommended Uses Universal cleaner for home, institutes, plant and machinery. compatible with all type of surfaces. Method of Application Dosing Method The most economical method of using "Stanrose® SPOL" is by recirculation washing, using tank cleaning machines. Make up a solution of 1 – 5% in preferably fresh water in the tank and re-circulate. Whenever possible, the cleaning solution should be heated to 50 - 80°C. Rinse off with hot fresh water. Alternatively, hand spray the tank with a 20 – 50% solution of "Stanpol-1006" and allow to stay for 30 – 60 minutes before a final rinse with hot water. When the tank is cleaned to a “water white standard”, remove any free water and ventilate until the tank is dry. Sampling and Tasting : For the removal of traces of hydrocarbons to a hydrocarbon free wall wash test specification prior to loading of sensitive cargoes. "Stanpol-1006" may also be used as a general purpose economical tank cleaning detergent. Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

ESD Epoxy Topcoats STAROXY NPE CRC 90 Description: - Staroxy NPE CRC 90 is a 100% solids epoxy Novolac coating ideal for harsh chemical and solvent resistant applications. It is used in secondary containment, solvent storage, pump pads, trenches, and other high exposure areas. Novolac Epoxy - Highly Chemical Resistant Epoxy - is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities. It is commonly used as a seal coat for Epoxy Mortar Systems where chemical resistant performance is required. Advantages: - Exhibits excellent resistance to strong acids, alkalis, and most industrial chemicals and solvents Can be applied in cool damp conditions Can be re-coated in 4 to 6 hours Can be applied in occupied facilities Forms a virtual moisture barrier 100% solids - 0.0 lbs VOC - meets even the most strict low VOC requirements Technical Properties: - Color: RAL shades Solids Content: 100% Gloss 60 F: 100 Mix Ratio: 2.1-A to 0.9-B by weight Pot Life: 20 minutes @ 75 F VOC: 0% Foot Traffic: 10-12 hours Recoat - Minimum: 4 - 12 hours (Depending on Temperature) Recoat - Maximum: 24-36 hours (Depending on Temperature) Service: 5 days Mechanical Properties: - Tensile Strength ASTM-D-638: 10,400 p.s.i Adhesion to concrete ACI Committee 403: 300 p.s.i - 100% concrete failure Hardness ASTM-D-2240: 86 Shore D Abrasion Resistance ASTM-C-501: CS-17 Wheel 30 mg lost Service Temperature MIL- D-3134F: Up to 180-325 degrees F. Dry Heat Elongation: 2.5% STAROXY CRC 90 Description: - Staroxy CRC 90 is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkaline for both interior and exterior applications. Advantages: - Excellent chemical resistance Strong yet resilient Built in flexibility Sprayable Technical Properties: - Mix Ratio: 2.5-A : 1.5-B By Weight Viscosity (mixed): 1800 CPS Pot Life (200 gr.): 40 minutes Tack Free to Touch: 6-8 Hours Initial Cure: 24 Hours Final Cure: 7 Days Packaging (unit size): 3 ltr. 15 ltr. Standard Colors: Black, White, & standard colors Mechanical Properties: - Tensile Strength (ASTM D-638): 5500 p.s.i. min. Elongation: 5%+ STAROXY CRC 80 Description: - Staroxy CRC 90 is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkaline for both interior and exterior applications. Advantages: - Excellent chemical resistance Strong yet resilient Built in flexibility Sprayable Technical Properties: - Mix Ratio 2.5-A : 1.5-B By Weight Viscosity (mixed): 2000 to 2500 CPS Pot Life (200 gr.): 40 minutes Tack Free to Touch: 4 to 8 Hours Initial Cure: 24 Hours Final Cure: 7 Days Packaging (unit size): 3 ltr. 15 ltr. Standard Colors: 15 Colors + Special Mechanical Properties: - Tensile Strength (ASTM D-638): 5500 p.s.i. min. Elongation: 5%+

STAROXY NPE CRC 90 Description: - Staroxy NPE CRC 90 is a 100% solids epoxy Novolac coating ideal for harsh chemical and solvent resistant applications. It is used in secondary containment, solvent storage, pump pads, trenches, and other high exposure areas. Novolac Epoxy - Highly Chemical Resistant Epoxy - is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities. It is commonly used as a seal coat for Epoxy Mortar Systems where chemical resistant performance is required. Advantages: - Exhibits excellent resistance to strong acids, alkalis, and most industrial chemicals and solvents Can be applied in cool damp conditions Can be re-coated in 4 to 6 hours Can be applied in occupied facilities Forms a virtual moisture barrier 100% solids - 0.0 lbs VOC - meets even the most strict low VOC requirements Technical Properties: - Color: RAL shades Solids Content: 100% Gloss 60 F: 100 Mix Ratio: 2.1-A to 0.9-B by weight Pot Life: 20 minutes @ 75 F VOC: 0% Foot Traffic: 10-12 hours Recoat - Minimum: 4 - 12 hours (Depending on Temperature) Recoat - Maximum: 24-36 hours (Depending on Temperature) Service: 5 days Mechanical Properties: - Tensile Strength ASTM-D-638: 10,400 p.s.i Adhesion to concrete ACI Committee 403: 300 p.s.i - 100% concrete failure Hardness ASTM-D-2240: 86 Shore D Abrasion Resistance ASTM-C-501: CS-17 Wheel 30 mg lost Service Temperature MIL- D-3134F: Up to 180-325 degrees F. Dry Heat Elongation: 2.5% STAROXY CRC 90 Description: - Staroxy CRC 90 is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkaline for both interior and exterior applications. Advantages: - Excellent chemical resistance Strong yet resilient Built in flexibility Sprayable Technical Properties: - Mix Ratio: 2.5-A : 1.5-B By Weight Viscosity (mixed): 1800 CPS Pot Life (200 gr.): 40 minutes Tack Free to Touch: 6-8 Hours Initial Cure: 24 Hours Final Cure: 7 Days Packaging (unit size): 3 ltr. 15 ltr. Standard Colors: Black, White, & standard colors Mechanical Properties: - Tensile Strength (ASTM D-638): 5500 p.s.i. min. Elongation: 5%+ STAROXY CRC 80 Description: - Staroxy CRC 90 is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkaline for both interior and exterior applications. Advantages: - Excellent chemical resistance Strong yet resilient Built in flexibility Sprayable Technical Properties: - Mix Ratio 2.5-A : 1.5-B By Weight Viscosity (mixed): 2000 to 2500 CPS Pot Life (200 gr.): 40 minutes Tack Free to Touch: 4 to 8 Hours Initial Cure: 24 Hours Final Cure: 7 Days Packaging (unit size): 3 ltr. 15 ltr. Standard Colors: 15 Colors + Special Mechanical Properties: - Tensile Strength (ASTM D-638): 5500 p.s.i. min. Elongation: 5%+

Stanrose® PWD Combitreat Stanrose® PWD Combitreat is a dry powder compound containing alkaline mineral salts, sequestering agents, scale and corrosion inhibitors and scale conditioners. Common Name Combitreat Powder BWT Product Code STAN-CLC152 Features and Benefits Complete ‘one-shot’ conditioning treatment for simplified dosing and handling. Boiler kept at peak level efficiency. Heating surfaces maintained at optimum thermal conditions. Promotes protective films to prevent boiler steel corrosion. Dispersant action suspends sludge and sediment particles. Reduced maintenance due to complete conditioning of water and internal boiler surfaces. Technical Properties Appearance - Light brown powder Condition - Free flowing pH - 11 @ 20o C Recommended Uses Suitable for use with all auxiliary boilers; smoke and water tube boilers; steam/steam generators, up to 20 bar pressure Method of Application The main attributes of Stanrose® PWD Combitreat fall into the following categories : Alkalinity control: The correct level of alkalinity ensures that the optimum environment exists for:- Correct precipitation of hardness salts in conjunction with phosphate Neutralisation of acid conditions Avoidance of caustic corrosion Control of magnesium and calcium salts The alkalinity ‘balance’ is extremely important for efficient water treatment. Stanrose® PWD Combitreat provides this whilst avoiding excessive pH levels which could cause embitterment and corrosion of boiler components. Hardness control: Stanrose® PWD Combitreat provides a phosphate reserve to effectively react with and precipitate the hardness salts introduced with the feedwater. The formation of insulating scale on hot metal surfaces is prevented as the scales produced will not adhere and so optimum heat transfer efficiency is maintained. The stable phosphate compounds used in Stanrose® PWD Combitreat will maintain their efficiency throughout the boilers normal operating temperature range. A temporary ‘phosphate hideout’ where low phosphate levels at certain temperatures are experienced, is thus avoided. Sludge Conditioning: Boiler sludge can most easily be removed by blow down if it is free flowing. Stanrose® PWD Combitreat will ensure this by preventing the scales from coalescing to form large crystals or adhering to metal surfaces. The resulting sludge is composed of small particles which are dispersed so that it will flow towards the bottom of the boiler to be removed by blow down. Storage and Handling Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose®Control C Product Description : “Stanrose® Control C” is a concentrated liquid neutralizing agent for corrosion control in condensate and feed water systems. Technical Review : Carbon dioxide enters the condensate system in two ways :- (a) As a dissolved gas. (b) As a decomposition product of soluble carbonates and bicarbonates , carbon dioxide vaporizes from the boiler and forms carbonic acid when it condenses with the condensate lowering the pH, iron and copper will enter into solution more rapidly as pH decreases causing an increase in corrosion rate. Within the condensate system and deposition of metallic oxides in the boiler “Stanrose® Control C” is quickly volatilised in the boiler and travels with the stream. In this way, it is able to neutralize carbon dioxide at all points through out the system, “Stanrose® Control C” effectively protects condensate areas against grooving or channeling and prevents the frequent failure at threaded points caused by low pH attack. Common Name Condensation Control Product Code STAN-BWT148 Features and Benefits Soluble in all proportions in water. Protects vapour and condensate areas from low pH corrosion. Protects copper and copper base alloys as well as iron and steel. Mild cleaning action, increasing heating efficiencies. Technical Properties Increase or decrease the recommended dosage according to the chart below : All Boiler Systems Condensate pH form Testing Less than 8.3 Increase Dosage by 25% for 72 8.3 – 9 Satisfactory maintain dosage 9.0 + Decrease dosage by 25% for 72 hour and retest Recommended Uses Requires minimum of testing and control. Can be fed alone or with other treatment chemicals. Does not break down to ammonia which is harmful to copper. Boiling point over 93°C / 204°F’ Method of Application “Stanrose® Control C” is a liquid, volatile alkaline amine which neutralizes the acid contaminants of condensate and feed water systems thus preventing the acid corrosion of system components. The most common cause of acid corrosion in condensate and feed water systems is the dissolved carbon dioxide (CO2) being present in the water evaporating. “Stanrose® Control C” neutralizes these acids and maintains the condensate and feed water in an alkaline condition. Dosage : The condensate is tested of pH to determine the dosage level. The minimum pH should be 8.3, the optimum would be between pH 8.3 and 9.0. A typical dosage for an average 10 metric tone system would be 0,5-1 liter per day. Below is a chart with the recommended limits for levels of treatments. They are not intended to replace either shipping company instructions or boiler manufacturer’s policy. “Stanrose® Control C” dosage cannot be calculated as closely as dosages for other treatment chemicals. Table below provides a starting dosage, but the ultimate dosage should be based on the pH actually developed in the condensate. In system starting to use “Stanrose® Control C” for the first time the feed rate should be started at 25% of the external dosage. The dosage can be increased in 25% increments at 3-4 week intervals. This technique will avoid sweeping excessive amounts of old corrosion products dislodged by “Stanrose® Control C” back into the boiler. Storage and Handling Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File