Search Results

Stanrose® Fostreat BWT Stanrose® Fostreat BWT is a dry powdered phosphate based treatment used to precipitate calcium hardness as a non adherent sludge. Stanrose® Fostreat BWT is a free-flowing white powder which is readily soluble in water. When Stanrose® Fostreat BWT is added to the boiler water under proper conditions it supplies the necessary phosphate to chemically react with calcium hardness to prevent the formation calcium carbonate, sulphate and/or silicate scales. The reaction between calcium and phosphate produces a finely divided non adherent sludge (calcium phosphate) which remains suspended in the boiler water and removed through blowdown. Common Name Fostreat Product Code STAN-BWT153 Features and Benefits Scale problems eliminated. Sludge problems greatly reduced. Easily dissolves in water to prepare feed solutions. 100 % active material. Dry product minimizes shipping cost. Feed solutions up to one pound per gallon possible. Technical Properties Dosage Chart : 1. Find your boiler operating pressure on left. 2. Find your phosphate test results as ppm PO4 across the top. 3. Read across from your operating pressure until you reach the column with your ppm PO4 results. This square will give you the correct dosage of Stanrose® Fostreat BWT to reach the correct protection for your boiler. Dosage table in grams/ton is described in technical data sheet. Recommended Uses Stanrose® Fostreat BWT is used in controlled amount so as to maintain a free phosphate residual in the boiler water. The control limits for phosphate normally are in the 20 to 60 ppm range. Exact parameters will be sent by our representative for your installation. The feed rate for Stanrose® Fostreat BWT will vary depending upon the calcium hardness of the make up water. Method of Application Dissolve in warm water and slug feed intermittently to the boiler feed water line or with a continuous feed pump to the boiler. Fostreat can be mixed with other treatment chemicals used for internal treatment. Material of construction of the feed equipment are not critical, but dissimilar metals should be avoided. Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Corrosion Inhibitor A corrosion inhibitor is a substance when added in a small concentration to an environment reduces the corrosion rate of a metal exposed to that environment. Inhibitors often play an important role in the oil extraction and processing industries where they have always been considered to be the first line of defence against corrosion. Common Name Corrosion Inhibitor BWT Product Code STAN-BWT155 Features and Benefits Minimises scale formulation, corrosion and sludge accumulation Simple to Control Effective iron dispersant Technical Properties Density [g/ml] - 1.45 - 1.47 Form - Liquid Freezing Point [°C] - <-20 Materials compatibility - Polypropylene, PVC, Polyethylene, Nylon, Stainless Steel, Viton, Buna –N, Neoprene, Butyl Rubber, Nitrile Rubber, CAF, PTFE pH - 14 Not Compatible - Aluminium, Brass, Copper, Zinc, Light Alloys, Natural Rubber Recommended Uses Maintains sludge in a non-adherent state for removal by blow down Simple test to determine level of treatment Can be used for boilers of all pressures Method of Application Dosing Method BWT Liquid Plus is best applied neat or diluted with condensate or evaporated water to any convenient strength and applied on a continuous basis using a suitable chemical dosing pump. Sampling and Testing Control is by simple boiler water tests for alkalinity. Dosing and Control The dosage rate of BWT Liquid Plus sufficient to produce a P alkalinity in the boiler water of 100ppm is 0.4 liters/1,000 liters of water. BWT Liquid Plus is strongly alkaline. Tanks and feeding equipment should be constructed of suitably resistant material such as polypropylene, PVC, polyethylene, mild steel, cast iron or stainless steel. Avoid the use of brass or light alloys. Storage and Handling Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Electrosolve Slow Dry Stanrose® Electrosolv Slow Dry are cold degreasing safety solvents. They combine the best cleaning - qualities of the inflamable solvents and carbon tetra chloride, but eliminate the explosive and toxic dangers of these products. They are designed for degreasing and cleaning electrical equipments such as motors and generators, circuit breakers, distribution panels, machinery, instruments, etc. Additionally these cleaners are very effective for removing dust particulars and oils where water washing is cumbesome, messy, troublesome or rust promoting. Common Name Slow Dry Electrical Cleaner Product Code STAN-CLC080 Features and Benefits Low Toxic Non-Corrosive Non Explosive Non Conductive Non Flammable Technical Properties Refer technical data sheet Recommended Uses Stanrose® Electrosolv Slow Dry, having in common a high cleaning capacity, differ from each other in a number of special characteristics. In this way they give a broad range of applications and make it possible to tackle various problems with the best possible results. Slow dry, slower evaporation rate than fast dry Non Flame This most effective product can be used confidently in areas where Inflammable products are prohibited. Also particularly suitable for cleaning of precision and electronic instruments. Method of Application Stanrose® Electrosolv Slow Dry, having in common a high cleaning capacity, differ from each other in a number of special characteristics. In this way they give a broad range of applications and make it possible to tackle various problems with the best possible results. Slow dry, slower evaporation rate than fast dry Non Flame This most effective product can be used confidently in areas where Inflammable products are prohibited. Also particularly suitable for cleaning of precision and electronic instruments. Storage and Handling Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose®Control C Product Description : “Stanrose® Control C” is a concentrated liquid neutralizing agent for corrosion control in condensate and feed water systems. Technical Review : Carbon dioxide enters the condensate system in two ways :- (a) As a dissolved gas. (b) As a decomposition product of soluble carbonates and bicarbonates , carbon dioxide vaporizes from the boiler and forms carbonic acid when it condenses with the condensate lowering the pH, iron and copper will enter into solution more rapidly as pH decreases causing an increase in corrosion rate. Within the condensate system and deposition of metallic oxides in the boiler “Stanrose® Control C” is quickly volatilised in the boiler and travels with the stream. In this way, it is able to neutralize carbon dioxide at all points through out the system, “Stanrose® Control C” effectively protects condensate areas against grooving or channeling and prevents the frequent failure at threaded points caused by low pH attack. Common Name Condensation Control Product Code STAN-BWT148 Features and Benefits Soluble in all proportions in water. Protects vapour and condensate areas from low pH corrosion. Protects copper and copper base alloys as well as iron and steel. Mild cleaning action, increasing heating efficiencies. Technical Properties Increase or decrease the recommended dosage according to the chart below : All Boiler Systems Condensate pH form Testing Less than 8.3 Increase Dosage by 25% for 72 8.3 – 9 Satisfactory maintain dosage 9.0 + Decrease dosage by 25% for 72 hour and retest Recommended Uses Requires minimum of testing and control. Can be fed alone or with other treatment chemicals. Does not break down to ammonia which is harmful to copper. Boiling point over 93°C / 204°F’ Method of Application “Stanrose® Control C” is a liquid, volatile alkaline amine which neutralizes the acid contaminants of condensate and feed water systems thus preventing the acid corrosion of system components. The most common cause of acid corrosion in condensate and feed water systems is the dissolved carbon dioxide (CO2) being present in the water evaporating. “Stanrose® Control C” neutralizes these acids and maintains the condensate and feed water in an alkaline condition. Dosage : The condensate is tested of pH to determine the dosage level. The minimum pH should be 8.3, the optimum would be between pH 8.3 and 9.0. A typical dosage for an average 10 metric tone system would be 0,5-1 liter per day. Below is a chart with the recommended limits for levels of treatments. They are not intended to replace either shipping company instructions or boiler manufacturer’s policy. “Stanrose® Control C” dosage cannot be calculated as closely as dosages for other treatment chemicals. Table below provides a starting dosage, but the ultimate dosage should be based on the pH actually developed in the condensate. In system starting to use “Stanrose® Control C” for the first time the feed rate should be started at 25% of the external dosage. The dosage can be increased in 25% increments at 3-4 week intervals. This technique will avoid sweeping excessive amounts of old corrosion products dislodged by “Stanrose® Control C” back into the boiler. Storage and Handling Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Electrosolv Stanrose® Electrosolv is an excellent Electric Parts cleaneing solvent. It is a perfect blend of non-chlorinated degresol with surfactants which help in degreasing and cleaning electrical equipments. The application of this product is very easy and it can be used for all electrical equipments. It is suitable to use on painted or varnished metal surfaces too. It may have an adverse effect on rubber or plastic. It is advisable to either remove the rubber or plastic parts if possible, or experiment on small portion of such parts before use. The Salient features of Stanrose® Electrosolv are that it provides immediate and efficient cleaning with quick drying property. It has high dissolving and penetration action so easily mixes with solvents and helps cleaning even heavy dirt. It is safe on applied electrical insulation and it is non corrosive nature makes it easier to use even on painted and varnished surfaces without causing any harm to it. It does not contain chlorinated solvents. It has excellent degreasing and emulsification power even for toughest dirt and grime. It can be used as an alternative to conventional electric cleaners. It has eco friendly components making it environment safe product for power generation industry. Common Name Electrical Cleaning Solvent Product Code STAN-CLC080 Features and Benefits Odorless, non-emulsifying degreasing agent and non-conductive electro cleaner Special degreasing agent for the removal of oil and grease from machines and motor parts, transmissions, ball bearings, gear wheels, metal parts, electrical components, etc. Odorless. Contains no chlorinated hydrocarbons or other harmful chemicals. Does not emulsify in water - the polluted oil can be separated by means of an oil / water separator. High flash point. Technical Properties Clear, odourless, fluid neutral degreasing agent based on among other things, high boiling aliphatic hydrocarbon. Stanrose® Electrosolv evaporates without residue. Stanrose® Electrosolv can be used on most metals, synthetic material, rubber and hardened metals, electrical components. Specific gravity (20°C) : 0.758 Flashpoint : 62°C pH : 7 Recommended Uses Stanrose® Electrosolv can be applied with a brush or by spraying the parts to be cleaned. This product can also be used by filling an immersion bath to clean extremely dirty parts. The high flash point and the fact that it is practically odorless makes Stanrose® Electrosolv a pleasant and problem free product. Method of Application Immersion Baths Stanrose® Electrosolv is used undiluted and unheated in immersion baths. Put the parts to be cleaned in the bath and soak for several hours. Thereafter, take the parts out of the bath and spray off with a forceful water-jet. Attention: parts that need to be rust free and dry (such as electrical components) should not be sprayed clean with water but with clean Stanrose® Electrosolv and afterwards should be blow-dried completely because of fire risk if residues are left behind. For the cleaning of dirty parts and surfaces use Stanrose® Electrosolv undiluted. Moisten the parts to be cleaned thoroughly with the product. Depending on the measure of dirt, soak the product for 5 to 60 minutes, brush in between. After this, rinse thoroughly with water. Attention: parts that need to be rust free and dry (such as electrical components) should not be sprayed clean with water, but with Stanrose® Electrosolv and afterwards should be blow dried completely to avoid fire risk. Storage and Handling Cold cleaners should only be used in combination with oil/water separators. To guarantee an optimal oil/water separation, cold cleaners should never be used with greater amounts of emulsifying cleaners (e.g. of High Pressure Cleaners) if the waste is passing oil/water separators. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Seacare OSD-II Dispersants are specially designed oil spill products that are composed of detergent‐like surfactants in low toxicity solvents. Dispersants do not remove oil from the water, but instead break the oil slick into small droplets. These droplets disperse into the water and are further broken down by nature. Dispersants also prevent the oil droplets from coming back together and forming another surface slick. Dispersed oil droplets are less likely to stick to birds and other animals, shoreline rocks, and vegetation. Common Name Oil Spill Dispersant, Type-II Product Code STAN-CLC060 Features and Benefits “Stanrose® Seacare OSD-II” is water based, clear, homogenous & non-flammable liquid. It is completely biodegradable & soluble in fresh & seawater. It is approved as a Type II dispersant according to LR448 specifications by the Department for Environment, Food & Rural Affairs (DEFRA). Technical Properties Colour Light Amber liquid Appearance Clear homogenous free flowing liquid. Cloud Point -7°C S R Gravity 0.95 to 1.05 (typical 1.04) Solubility Soluble in water. Shelf Life 5 Years. Flash Point Non-Flammable Toxicity Non-Toxic Viscosity 132 cSt at room temperature pH Value 6.0 to 8.5 Prohibited Items Does not contain chlorinated hydrocarbons, phenols, cresols, Caustic alkali, or free mineral acids Biodegradability Biodegradable Recommended Uses Dispersants can be applied to oil slicks either by aircraft or by ships with spraying equipment. They are also used by injection below water to break up oil before it reaches the surface. The use of dispersants is restricted under the National Oil and Hazardous Substances Pollution Contingency Plan (NCP). Federal and state agencies have agreements establishing areas where rapid decisions on dispersants may be made by the federal on‐scene coordinators. Areas outside those designated require additional approval of other agencies identified in the NCP. Method of Application CHEMICAL DISPERSANT APPLICATION : “Stanrose® Seacare OSD-II” contains surface-active agents (surfactant) and a stabilizer. The purpose of Stanrose® Seacare OSD-II is quick removal of oil on surface by converting it in fine oil in water emulsion, which is rapidly distributed through the water column through agitation and mixing. Oil dispersed effectively into large volume of seawater is further diluted rapidly by turbulence and its concentration is reduced soon to background levels. The objective of “Stanrose® Seacare OSD-II” is chemical dispersion of Oil spillage an expose of larger area of oil attack by marine bacteria present in sea water than the exposed area of untreated slick. This is achieved when surface oil breaks into droplets by action of Stanrose® Seacare OSD-II which on agitation disposes in to vertical water Column of sea. These droplets are rapidly biodegraded by marine bacteria. Resurfacing of droplets is influenced by droplet size, density of seawater, depth of water column and viscosity of oil being treated. The smaller the droplets size the less chance of oil Resurfacing and more rapid the dilution of droplet and its biodegradation by marine Bacteria and greater its anti cohesive properties. FEEDING & DOSAGE : AERIAL SPRAYING : Aircraft provide the most rapid method of applying dispersants to an oil spill and a variety of aircraft can’ be Used for spraying. For aerial spraying, Stanrose® Seacare OSD-II is used undiluted. A typical treatment rate is 10 to 50 ltrs per Acre or a DOR (dispersant to oil ratio) of 1:50 to 1:20. Normally oil thickness is 100 to 200 microns and it would Spread it to 2 ton of oil per hectare (lhectre=6. lacres). However, this can vary depending on the type of oil, degree of weathering, temperature and thickness of oil slick, typical application attitudes of 30 to 50 feet have been used, although higher altitudes may be effective under certain conditions. Actual effective altitudes will depend on the application equipment, weather and aircraft. Careful selection of spray nozzles is critical to achieve desired dose levels, since droplet size must be controlled. Many nozzles used for agricultural spraying are of low capacity and produce too fine a spray. A quarter-inch open pipe may be all that is necessary if the aircraft travels at i9 (I or more, since the air shear at these speeds will be sufficient to break the dispersant into the proper sized droplets. BOAT SPRAYING : Stanrose® Seacare OSD-II may also be applied by workboats equipped with spray booms mounted ahead of the bow wake or as far forward as possible. The preferred and most effective method of application from a workboat is to use a low-volume, low-pressure pump so the chemical can be applied undiluted. Spray systems, which apply Dispersant neat undiluted, are preferable. However, if this is not practical, water dilatable systems which provide a 10% dispersant concentration should be used. Stanrose® Seacare OSD-II is formulated to be diluted with seawater if Necessary during application, since the product is active at very low dosage. The mixture of dispersant and seawater is then discharged through booms having several nozzles. Stanrose® Seacare OSD-II should be applied as droplets, not atomized, Natural wave or boat wake action usually provides Adequate mixing energy to disperse the oil. It can be seen from the above that Stanrose® Seacare OSD-II serves as both TYPES and TYPE 2 oil spill dispersant. As a guideline one (1)ltr of Stanrose® Seacare OSD-II is capable of dispersing atleast 30 ltrs of heavy petroleum oil. Our product Stanrose® Seacare OSD-II composition meets the criteria for not being harmful to the marine environment according to MARPOL Annex V and may be discharged into the sea when used to clean oil on sea water surface. Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Liquid Descaler A fully inhibited, fast acting descaler. Common Name Scale Remover - Liquid Product Code STAN-CLC073 Features and Benefits Add “Stanrose® Liquid Descaler” slowly, a few gallons at a time, to the tower to reduce tendency to foam. Foaming indicates that descaler is dissolving the scale. If excessive foam occurs, use Defoamer. Any method of descaling either boilers or towers will dissolve scale that may be plugging areas that are already leaking due to rust or other corrosion, therefore, no liability can be assumed. Technical Properties Contains a balanced ratio of acids and surfactants, making it a suitable descaler for boilers and water towers. It contains built-in pH indicator. Contains acids. Do not use on aluminum, decorative metals, zinc, magnesium, galvanized or painted surfaces. Spot test small area for sensitivity before use. Recommended Uses For Descaling Boilers and Water Towers Method of Application For Descaling Boilers : For initial descaling, mix 1 part “Stanrose® Liquid Descaler” with 5 parts water in the system. Later cleaning may require less concentration. Isolate unit to be cleaned to protect valves and avoid possible contamination of rest of system. Fill boiler with “Stanrose® Liquid Descaler” and water at a 1:5 to 1:20 ratio. Heat the water to 60oC-80oC (140oF-190oF) and circulate for about 4 hours and then check the tubes. If descaling is not complete, refill the boiler with “Stanrose® Liquid Descaler” and water and repeat. Drain the boiler and flush with water pressure to remove all the scale and sludge. Drain and fill the boiler at least 3 times. For Descaling Water Towers : Shut tower down and use high pressure water to hose out mud, silt and slime. Isolate the unit to be descaled to protect valves and avoid possible contamination of the rest of system. Lower water level to just the amount required for circulation. Add “Stanrose® Liquid Descaler” to water in the tower at the ratio of 1 part in 5 parts of water. Add enough “Stanrose® Liquid Descaler” to maintain the pH from 1.5 to 2.5. Continue adding, as required, to maintain proper pH level for about 4 hours. The circulating solution should be yellow in color. If the solution while circulating turns blue, more “Stanrose® Liquid Descaler” needs to be added. Drain the system, flush and fill twice and check pH of water to be certain all “Stanrose® Liquid Descaler” has been removed. Storage and Handling Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Gum Remover “Stanrose® Gum Remover” is designed to soften and remove residues of chewing gum from floors, carpets, and upholstery. Rapidly lifts chewing gum from carpets and porous surfaces without the need for damaging freeze sprays Use as supplied Suitable for use on most carpets and upholstery within schools, hospitals, leisure complexes and other public areas Heavy duty performance even on old and trodden-in gum Citrus fragrance Common Name Chewing Gum Remover Product Code STAN-CLC108 Features and Benefits Viscous preparation allows precise application and prevents the need for reapplication Removes even the most stubborn gum residue Specialist solvents penetrate around and under the gum softening its bond to surfaces allowing it to be easily peeled. Easy peel prevents damage to the pile of carpets and upholstery. Contains emulsifiers to allow residues to be wiped away with water. No unsightly white marks. Citrus fragrance. Technical Properties APPEARANCE Viscous liquid COLOUR Colourless ODOUR Citus solvent. FLASH POINT (°C) - 4 closed cup SOLUBILITY Emulsifies in water RELATIVE DENSITY 0.72 Recommended Uses Ideal for the removal of chewing gum in all areas where this represents a problem for example in schools, leisure centres, hotels, busses and trains. Method of Application 1. When applying to fabric or carpets test an inconspicuous area first for colour fastness 2. Apply over and around the gum to allow it to penetrate underneath. 3. Allow to penetrate and soften the gum. 4. Peel away the gum with a scraper. 5. Wipe away residues with a damp cloth. Note : when removing gum from non-porous surfaces first score the surface of the gum to allow more rapid penetration. Do not apply to tarmac or asphalt. Storage and Handling Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Keep away from heat, sparks and open flame. Avoid inhalation of vapours. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Seacare OSD-I Stanrose® Seacare OSD-I” is a biodegradable hydrocarbon based product with high dispersing efficiency and low toxicity. It is approved as a Type I dispersant according to LR448 specifications by the Department for Environment, Food & Rural Affairs (DEFRA) formerly the UK Ministry of Agriculture, Fisheries and Food (MAFF). Common Name Oil Spill Dispersant, Type-I Product Code STAN-CLC059 Features and Benefits Stanrose® Seacare OSD-I is used to disperse and clear accidental oil spills on deck and in the sea. It can be used as Tank Cleaner for crude oil and paraffin Contaminations. TANK CLEANING Product can be used as a tank cleaner for the removal of heavy oil contaminations like crude oil, paraffin etc. It can be used in combination with Stanrose® Sea Clean or Stanrose® Bio-Degreaser HP. Technical Properties Form Liquid Appearance Amber Density 0,8 Flash Point Above 61 Not Compatible Do not use with natural rubber, may swell synthetic rubber Recommended Uses OIL SPILL ON WATER Where possible contain any floating spilled oil, using oil booms. If the oil layer is too thick, pump or skim off as much as possible. When most of the spilled oil has been removed or the spilled oil cannot be contained, apply undiluted. For small spills, spray using a portable hand spray. Allow the product to react with the oil, then disperse the mixture using water from fire hose or other mechanical means. For large spills, use spraying equipment connected to the side of a motor boat. Ensuring the spray is directed over the spill. Spraying can also be done from aircraft fitted with spraying equipment. OIL SPILL ON DECKS AND BEACHES Remove as much spilled oil as possible with oil absorbent. Spray undiluted over the spill and allow the product to react with the oil. Disperse the mixture with water from a fire hose. For spills on beaches and on rocks the mixture will be dispersed by natural tidal wash action. Method of Application TANK CLEANING – CIRCULATION METHOD Recommended tank-cleaning procedure for removing stains from tank linings using Stanrose® Seacare OSD-I. 1. Mix solutions of Stanrose® Seacare OSD-I either in tank bottom or void space. 2. Dilution rate with water between 4 % and 10 %, depending upon light or heavy contamination (see above). Recent experience has shown that a 8 % - 8.5 % solution secures successful cleaning. To boost up the cleaning, an additional shot of 2 – 3 % Stanrose® Sea Clean or Stanrose® Bio-Degreaser HP an be added to the metering tank. 3. Do not use the entire quantity of Oil Spill Dispersant Type 1 in one solution for all tanks to be cleaned. Save a few drums (2 - 3) to “boost” the solution for cleaning the last 20 % - 25 % of the 4. Tanks to be cleaned. 5. The solution may be used at ambient temperature, however, it is suggested that an increase of the cleaning temperature to maximum 50 °C will enhance the cleaning ability and shorten the cleaning time. 6. Proceed to recycle the cleaning solution through the tank washing system for a period of two hours minimum per machine drop. Usually a cleaning time of 4 hours per tank will prove sufficient. 7. At completion of chemical application begin washing down with water, using maximum pressure available. 8. Inspect tank surfaces and if there remain some stains, spot clean with undiluted Stanrose® Seacare OSD-I directly on the stained area. Allow a reaction time of 30 minutes and then rinse with water. Storage and Handling Store in a dry place, keep container closed when not in use. Avoid contact with skin. Wash with large quantities of water. In case of contact with eyes, treat with large volumes of water and see a physician. Avoid contact with eyes and skin. In case of contact rinse with plenty of water. Wear suitable protective clothing, gloves and eye/face protection. Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® BTC Stanrose® BTC is a biological product which has been specially formulated for the removal of stains and deposits on urinals and toilets. Stanrose® BTC can also be used in waterless urinal systems. It also helps reduce or eliminate odours associated with these systems. Stanrose® BTC is safe to use in Septic Tank Installations where the use of nasty chemicals is not advised. Stanrose® BTC is a completely natural toilet cleaner which is made of no hazardous chemicals and only naturally occurring bacterial products combined. This combined product is an excellent toilet cleaner and will leave a fresh clean smell. TECHNICAL INFORMATION Stanrose® BTC contains a blend of selected micro-organisms in a liquid formulation. These micro-organisms have been specially selected as being naturally occurring and for their ability to grow and produce a wide range of enzymes which help to degrade organic waste materials. Stanrose® BTC also contains a blend of surfactants designed to enhance the cleaning effect of the product and also to penetrate into deposits on surfaces. This also aids the microbial action by making a greater surface area available for microbial attack. All aspects of the formulation help to remove organic materials and prevent build up of deposits which can lead to off odours in toilets and urinals. This action helps to mobilise the organic material and transport it to the wastewater treatment plant where it can be properly treated. The chemical ingredients of the product are biodegradable so will not have an adverse effect on the operation of an effluent treatment plant. Common Name Biological Toilet Cleaner Product Code STAN-CLL094 Features and Benefits Cleans surfaces of deposits. Helps to digest organic waste down the drain line to prevent odours. Pleasantly scented to help deodorise the area. Safe for Use in Septic Tank Installations Can be used in conjunction with Waterless Urinal Units Technical Properties Form - Liquid Colour - Blue Scent - Zingy Lemon Shelf life - 12 months Recommended Uses The product contains natural ingredients designed to help dissolve lime scale and uric acid crystals. These ingredients are designed to have a gradual effect on scale removal and thus prevent significant build up. This helps to eliminate the need for the use of corrosive acids for this purpose. Method of Application 1. Toilets - Use daily as with a normal toilet cleaner. Lift the seat and apply Biosure Toilet Cleaner to cover the surface of the toilet bowl. Scrub with a toilet brush and leave product in contact with the surface for as long as possible. 2. Urinals - Use daily. Apply liquid to cover the surface. Scrub using toilet brush and leave on surface for as long as possible. Storage and Handling The microbial strains in our Stanrose® BTC are all naturally occurring. They have not been genetically engineered in any way. These microbial strains are recognised as being non-pathogenic to humans or animals. Stanrose® BTC does not contain any harsh chemicals. Store in cool, dry conditions. Keep away from direct sunlight or other sources of light. Storage temperatures should be between 5oC and 30oC. Further information on handling and storage of this product is provided in the Safety Data Sheet. This document should be studied carefully prior to use. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Clean Care Alkaline Non-caustic water based alkaline cleaner, containing corrosion inhibitors to prevent the corrosion of metals such as zinc, aluminium, copper, brass and tin. "STANROSE® CLEAN CARE ALKALINE" minimizes the hazards in handling caustic based materials. Common Name Alkaline Safety Liquid Product Code STAN-CLC054 Features and Benefits Non-caustic. Non-flammable Does not contain nonylphenol ethoxylates or other estrogenic compounds Non-corrosive to ferrous metals Suitable for all tank-coatings Can be used for gas and hydrocarbon-freeing of tanks Can be used for deodorizing Safe, meets current regulation Technical Properties Form - Liquid Appearance - Colourless Density - 1.1 pH in Conc - 13 pH in 1% Sol - 11. 4 Non Compatible - The concentrated product may react with aluminium, zinc, tin and their alloys. Recommended Uses It minimizes the hazards in handling caustic based materials. Method of Application Cargo tank cleaning following discharge of drying, semi-drying and non drying natural oils and fats. As soon as possible after the cargo has been discharged, the tanks should be flushed with cold water to prevent polymerisation and evaporation of the lighter oil fractions. Whenever possible, the cleaning solution should be heated to 60-80°C. However, the polymerising nature of some natural oils may demand lower cleaning temperatures. Dosing Method The most economical method of using "STANROSE® CLEAN CARE ALKALINE" is by direct injection followed by recirculation washing, using tank cleaning machines. If this method is not possible, hand spraying provides acceptable options. Refer to dosage table for dosage rates. Cargo Residue | Hand Spray | Re-Circulation | Direct Injection | *Approx. re-circulation consumption, litres per 1000 m3 tank space Fatty acids, fatty alcohols Fish oils | 100% | 3-5% | 2-4% | 180-300 Drying & Semi drying | 100% | 3-5% | 2-4% | 180-300 Vegetable oil | 50-100% | 2-4% | 1-3% | 120-240 Non drying vegetable oil | 50-100% | 2-4% | 1-3% | 120-240 *When using the re-circulation method, the tank to be cleaned is filled with water to a level that the heating coils are covered. As an average, this is approximately 0.6% of the volume of the tank. The figures mentioned in this column are the quantity of "STANROSE® CLEAN CARE ALKALINE" required to obtain the recommended solution strengths. Storage and Handling Keep away from heat, sparks and open flame. Ensure that the working area is well ventilated. Store at moderate temperatures in dry, well-ventilated area. Packing Available 25 Ltr. / 210 Ltr. Download File

Stanrose® Biocide “Stanrose® Biocide” is a liquid, pumpable algicide dispersion for water-based technical products. Due to the very low water solubility it is especially recommended for coating exposed to severe weathering. “Stanrose® Biocide” controls algal growth on paints and plasters on the exterior of buildings and so enhancing their aesthetic appearance. Common Name Biocide & Algaecide Product Code STAN-BWT154 Features and Benefits Miscibility/Solubility - Miscible with water. Virtually insoluble in water and organic solvents. Stability - The activity of the active ingredient is not changed by short-term temperature stress during processing at up to 100°C or in the pH-range of 4-10. Technical Properties These values do not constitute specifications Appearance - flowable, white to yellowish-greyish dispersion Density - 20oC 0.97 to 1.07 g/cm3 Viscosity η 20°C - 60 to 90 KU Particle size - 0 to 30 mm Recommended Uses “Stanrose® Biocide” is based on an active substance which is practically water insoluble. “Stanrose® Biocide” can therefore be used in appropriate paint formulations and coatings where it is exposed to weathering and periodically damp conditions. In addition to the inherent effectiveness of “Stanrose® Biocide” other factors are necessary for long term performance, e.g., formulation of the ready for use product and optimum dosage are also necessary. In extreme cases where, for example, faults in construction technology lead to the permanent wetting of particular areas, successful application of microbicidal paint can only be effective after the construction faults have been rectified. If on a coated surface, moulds or fungi are anticipated in addition to algae, the paint or plaster in question must be treated additionally with a suitable fungicide. “Stanrose® Biocide” is only an algicide. Therefore, it can replace neither an in-can preservative nor a fungicide. “Stanrose® Biocide” must be blended homogeneously with the product to be protected. It is recommended to add “Stanrose® Biocide” at the beginning of manufacturing processes. Method of Application Dosage : The optimum dosage necessary of a microbicide depends largely upon the contamination risk, the exposure conditions and the general susceptibility of the coating (paint or plaster) to microbial growth. For that reason, the concentration ranges listed below should be taken as general guidance only: Paints 0.2 - 1.0% Plasters 0.1 - 0.3% In case of intense exposure to weather, if condensed water is formed continuously or if the coats of paints or plasters get dirty very easily, the dosage of “Stanrose® Biocide” may have to be increased above the usual level. It is recommended to check planned dosages in laboratory experiments and if possible in practical experiments as well. Storage and Handling Please refer to the safety data sheet of this product for precise handling instructions. The processing and use of industrial chemicals require adequate technical and professional knowledge. In general, avoid eye and skin contact, wear safety goggles, gloves and protective clothing. In case of eye or skin contact despite precautionary measures, wash immediately and thoroughly with plenty of warm water and obtain medical attention. The legal requirements prevailing in your country, especially on working hygiene and in the avoidance of accidents, must be observed. “Stanrose® Biocide” should be stored in the closed original container. Protect from heat. Any supplies which do freeze must be homogeneously mixed after thawing before they can be used, no loss in effectiveness will be experienced. Storage for a longer period of time can lead to an increase of viscosity. Use biocides safely. Always read the label and product information before use. Packing Available 25 Ltr. / 210 Ltr. Download File